Crosman 70301 - Manual

70301
OWNER’S MANUAL
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS SIGHT
CenterPoint Precision Optics
7629 Routes 5 & 20
Bloomfield, NY 14469
United States of America
www.centerpointoptics.com
Made in China
1-866-726-1122 70301-515
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS ABOUT THE USE AND OWNERSHIP OF
THIS SIGHT.
Direct viewing of the sun can cause permanent eye damage. Do not attempt to
view the sun through this riflescope or any other optical instrument.
Always follow all rules of firearm and gun safety.
This product contains a chemical known to the state of California to cause can-
cer and birth defects (and other reproductive harm).
Learning the parts of your scope new sight
Learning the names of the parts of your new sight will help you to understand your owner’s manual.
1. Reflex lens
2. Elevation (vertical) adjustment
3. Windage (horizontal) adjustment
4. Elevation lock
5. Red/Green illumination dial
6. Multi-Reticle Dial
7. weaver-style rail mount
Mounting Procedure
CAUTION: Always ensure your rifle is UNLOADED, UNCOCKED and the safety is applied before fitting
the sight. Practice safe handling procedures at all times.
1. Locate the proper mounting position on your rifle.
2. Loosen the mounting screws (A and B) on the mount.
3. Install and adjust the sight to a proper position to suit your shooting preferences, then tighten the
mounting screws.
NOTE: Do not over tighten the screws as you could cause damage to the sight.
• The sight is now ready to be zeroed.
Sight Adjustment
The purpose of zeroing the sight is to ensure that the sight is aligned with the impact point of the bullet.
Before zeroing the sight, read the following adjustment instructions carefully.
1. Place a target 100 yards away.
2. Ideally use a steadying device such as a bipod or shooting stand, aim at the center of the target
and fire three test shots, if safe to do so.
3. If the impact point of the bullet grouping is exactly in the center of the target then the sight is
zeroed. If it is not, you will need to adjust the reticle using the elevation and/or windage adjust-
ments.
4. Using the provided tool loose the elevation lock.
5. Vertical Adjustment (Elevation) - Use tool to turn the adjusting knob as required. One click in
either direction equals 1 MOA.
6. Horizontal Adjustment (Windage) - Use your tool to rotate the adjusting knob as required. One
click in either direction equals 1 MOA.
7. Having adjusted the windage and elevation as required, fire, if safe to do so, another test shot.
Keep adjusting and test firing until the test shot impacts on the center of the target when the
reticle is on the center of the target. This is vital for accurate shooting.
8. Once the sight is zeroed, tighten the elevation lock and reconfirm your zero.
9. Adjustments may need to be made after changing reticles.
Red or Green Dot
1. Remove the battery cover from the red/green illumination dial by
turning the cover counter clockwise while holding the sides of
the illumination dial.
2. Install one CR2032 3V lithium battery into the compartment with
the “+” side up.
3. Replace the cover and tighten in by turning it clockwise, while
holding the sides of the illumination dial.
4. Turn the red/green illumination dial to illuminate the red or green
dot. The brightness will change as you turn the dial. The mark-
ings on the dial show the color and intensity of the light. Lining the “R” or “G” up with the dot will
turn the illumination off.
Selecting Reticle
1. Rotate the multi-reticle dial to the desired reticle, making sure to align
the dial with the indexing mark.
Maintenance
• Take care not to drop or knock the sight once it is zeroed.
• Keep the protective lens cover in place when the sight is not being used.
• Store the sight in a cool dry place when not in use.
• Be careful to avoid contact with acid, alkaline or corrosive chemicals.
• Do not attempt to lubricate any part of the sight.
• Do not disassemble the sight. Do not loosen or remove any screws or parts
not outlined in this manual. Any such or similar actions will void the warranty.
• Wipe the lens with a clean flannel cloth to keep it clean and dry. Do not use
finger or finger nail to touch or clean the lens.
• Use only a clean flannel cloth for cleaning.
• To maintain battery life, turn illumination off when not in use.
• For extended storage, remove the battery.
Specifications
Model 70301 Length (inches) 3.25”
Magnification 1x Weight (ounces) 5.5
Objective Diameter (mm) 32 W/E Adjust Click Value 1 MOA
Eye Relief (inches) Infinite Batteries 1: CR2032 3V Lithium
LIMITED LIFETIME WARRANTY ON CENTERPOINT PRODUCTS
Your CenterPoint™ product is warranted to be free of defects in materials and workmanship for the
lifetime of the original owner. This warranty does not cover damages due to fair wear and tear, failure
to provide routine maintenance, and does not include batteries or accessories. This warranty lasts as
long as the original purchaser owns the product, and is not transferable. In the event of a defect under
this warranty, we will, at our option, repair or replace the product provided our inspection indicates
that an original defect exists. CenterPoint reserves the right to replace any product which is no longer
available with a product of comparable value and function. If CenterPoint determines the repair is not
covered under the warranty guidelines, there could be a charge to you for the repair. This is a limited
warranty and does not cover damages caused by misuse, improper handling or installation or mainte-
nance provided by someone other than CenterPoint.
This limited warranty does not include consequential damages, incidental damages, or incidental
expenses, including damage to property or any other expense. CenterPoint disclaims any implied war-
ranties. Some states do not allow the exclusion or limitation of incidental or consequential damages,
or allow limitations on implied warranties so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state and country to country.
WARRANTY CLAIMS/ REPAIR SERVICE
If your product needs repair, call CenterPoint Customer Service at 1-800-726-1122 or visit our web
site at www.centerpointoptics.com DO NOT ATTEMPT TO DISASSEMBLE IT! Any disassembly or
modification not performed by CenterPoint Precision Optics will void the warranty.
USA Customers: Please contact CenterPoint before shipping your product. Include with product
your name, address, description of problem, phone number and copies of sales receipt and warranty.
A check or money order in the amount of $10.00 to cover the cost of postage and handling is also
required. Package and return to CenterPoint, Crosman Corporation, 7629 Rts. 5 & 20, Bloomfield, NY
14469. CenterPoint will not assume any responsibility for any loss or damage incurred in shipping.
International Customers: Please return product to your nearest distributor. If you do not know your
distributor, please call 585-657-6161 and ask for our International Department for assistance. Ship-
ping and handling costs may apply.