Crosman CP0427 - Manual

Model CP0427
Laser sight
Owner’s Manual
Read all instructions and Warnings in this manual before using the laser sight.
Centerpoint Precision Optics
7629 Rt 5 & 20
Bloomfield, NY 14469
1-866-726-1122 CP0427CB515
LASER RADIATION—
AVOID DIRECT EYE EXPOSURE
Laser Diode
Wavelength: 630-640 nm
Max Output: < 5 mW
Class IIIa
Laser Product
CAUTION: AVOID DIRECT EYE EXPOSURE. Laser emitted from the aperture.
CAUTION: A laser sight is not a toy. It must be used under the supervision of an adult. Improper use or careless use may
cause serious injury, especially to the eyes. Avoid direct eye exposure to the laser beam.
Always follow the safety instructions found in the owner’s manual and keep these instructions in safe place for future use.
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS ABOUT THE USE AND OWNERSHIP OF THIS LASER SIGHT
Dovetail Ring Weaver-Style Ring
Mounting Screws Mounting Screws
OR
1. SELECTING THE CORRECT MOUNT FOR YOUR GUN
The laser attaches to either a 3/8” grooved receiver (dovetail) found on most .22 rifles and air guns, or to a weaver-style base
as installed on most center fire pistols and rifles. The laser is shipped with the mounting ring for a weaver-style rail installed.
If you need to mount your laser to a 3/8” grooved receiver, loosen the two rail screws, and remove the weaver-style ring and
replace it with the dovetail ring.
2. ATTACHING THE MOUNT TO YOUR GUN
be certain that your gun is unloaded and pointing in a safe direction.
CAUTION: In order to avoid injury, keep the laser off until you are ready to aim and shoot. Make sure the laser is off when
you mount or remove the sight.
• Slide the appropriate rail onto your gun.
• Insert the laser into the mount, with the on/off switch towards the back of the gun.
• Turn the mount so that the elevation screw is on top, and the windage screw is on the right side.
• Tighten the mounting screws using the larger hex wrench.
3. ACTIVATING THE LASER
CAUTION: AVOID DIRECT EYE EXPOSURE. Laser emitted from the aperture.
A. INSTALLING THE BATTERIES This laser sight uses 2 (LR44) button cell batteries.
• Make sure the laser is pointed in a SAFE DIRECTION
• Remove the battery access cap (power switch) by turning counter-clockwise.
• Place 2 batteries inside (plus side up)
• Replace the battery access cap by turning clockwise until tight.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-
cad, ni-mh, etc.) batteries
• “Do not mix old and new batteries
B. USING THE STANDARD ON/OFF SWITCH
The laser sight is activated by pressing in the button switch. It is turned off by
the same procedure.
NOTE: Always be sure to turn off the switch after use to avoid draining the
battery.
C. USING THE REMOTE ON/OFF SWITCH
• Your laser also comes with a remote on/off switch which allows
you to turn the unit to turn the unit momentarily with pressure. To
install the pressure switch:
• Remove the standard battery access cap.
• Screw in the remote pressure switch.
• Use the enclosed adhesive strips to attach the on/off pad to a convenient location on your gun.
• The laser is activated while the pressure pad is pressed.
• The laser is de-activated by relieving the pressure on the pad.
4. SIGHTING IN THE LASER
Your laser sight may be adjusted
for both windage and elevation. To
determine what adjustments must
be made, fire 3 shots at a target. If
the point of impact is directly in the
center of the tartget, then the laser
sight is zeroed. Otherwise the sight
needs to be adjusted.
WINDAGE
Using the small hex wrench
included in your package, turning
the windage adjustment hex screw
clockwise will move your point of
impact to the right. While turning the
hex screw counter-clockwise will
move your point of impact to the left.
ELEVATION
Using the small hex wrench included in your package, turning the elevation adjustment hex screw clockwise will move your
point of impact up. While turning the hex screw counter-clockwise will move your point of impact down.
Note that the adjustments are very sensitive. One half rotation, 180 degrees, will provide approximately 10 inches of move-
ment at 25 yards. After adjustment, carefully fire three more shots, make additional adjustments as necessary.
NOTE: Do not adjust the flathead screw, this is used in manufacturing process only.
Caution: use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
SPECIFICATIONS
Output Power Class IIIa; <5mW
Wavelength 635-655nm
Dot Size .40” @ 10yds
Visible Range
Indoor lighting – 50yds
Outdoors at night – 200yds
Windage/Elevation Ajustment +/- 10ft. @ 100 yards
Tube Size 16mm
Length (Laser Only) 2.64 in.
Batteries 2 Button Cell Batteries
Warranty 1yr
Windage Screw
Laser Aperture On/Off
Switch
Elevation Screw
Battery
Access Cap
Remote Switch