Crosman 74252 - Manual

Model 74252
Laser sight
Owner’s Manual
Read all instructions and Warnings in this manual before using the laser sight.
Centerpoint Precision Optics
7629 Rt 5 & 20
Bloomfield, NY 14469
United States of America
1-866-726-1122 74252-515
LASER RADIATION—
AVOID DIRECT EYE EXPOSURE
Laser Diode
Wavelength: 630-640 nm
Max Output: < 5 mW
Class IIIa
Laser Product
CAUTION: AVOID DIRECT EYE EXPOSURE. Laser emitted from the aperture.
CAUTION: A laser sight is not a toy. It must be used under the supervision of an adult. Improper use
or careless use may cause serious injury, especially to the eyes. Avoid direct eye exposure to the laser
beam.
Always follow the safety instructions found in the owner’s manual and keep these instructions in safe
place for future use.
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS ABOUT THE USE AND OWNERSHIP OF
THIS LASER SIGHT
1. On/off switch (battery cap)
2. Laser aperture
3. Elevation screw
4. Windage screw
5. Remote switch
6. Mounting screws
7. Dovetail ring
8. Weaver-style ring
1. SELECTING THE CORRECT MOUNT FOR YOUR GUN
The laser attaches to either a 3/8” grooved receiver (dovetail) found on most .22 rifles and air guns, or to
a .852” weaver-style base as installed on most center fire pistols and rifles. The laser is shipped with the
mounting ring for a weaver-style rail installed. If you need to mount your laser to a 3/8” grooved receiver,
loosen the two mount screws, and remove the weaver-style ring and replace it with the dovetail ring.
Dovetail Ring Weaver-Style Ring
Mounting Screws Mounting Screws
OR
2. ATTACHING THE MOUNT TO YOUR GUN
BE CERTAIN THAT YOUR GUN IS UNLOADED AND POINTING IN A SAFE DIRECTION.
CAUTION: In order to avoid injury, keep the laser off until you are ready to aim and shoot. Make sure the
laser is off when you mount or remove the sight
1. Slide the appropriate mount onto your gun
2. Insert the laser into the mount, with the on/off switch towards the
back of the gun
3. Turn the mount so that the elevation screw is on top, and the wind-
age screw is on the right side
4. Tighten the mounting screws using the larger hex wrench
3. ACTIVATING THE LASER
CAUTION: AVOID DIRECT EYE EXPOSURE. Laser emitted from the
aperture.
A. INSTALLING THE BATTERIES This laser sight uses 2 (LR44) button cell batteries.
1. Make sure the laser is pointed in a SAFE DIRECTION
2. Remove the battery access cap (power switch) by turning counter-clockwise
3. Place 2 batteries inside (plus side up)
4. Replace the battery access cap by turning clockwise until tight
B. USING THE STANDARD ON/OFF SWITCH
The laser sight is activated by pressing in the button switch until it clicks. It is turned off by the same
procedure.
NOTE: Always be sure to turn off the switch after use to avoid draining the battery. When storing for an
extended period of time, remove the batteries.
C. USING THE REMOTE Momentary ON/OFF Pad
1. Your laser also comes with a remote on/off pad which allows you to turn the unit momentarily on or off
with pressure. To install the pressure switch. Remove the standard battery access cap (on/off switch)
2. Screw in the remote pressure switch
3. Use the enclosed adhesive strips to attach the on/off pad to a convenient location on your gun.The
laser is activated while the pressure pad is pressed
4. The laser is de-activated by relieving the pressure on the pad
4. SIGHTING IN THE LASER
Your laser sight may be adjusted for both windage and elevation. To determine what adjustments must
be made, fire 3 shots at a target. If the point of impact is directly in the center of the tartget, then the
laser sight is zeroed. Otherwise the sight needs to be adjusted.
WINDAGE
Using the small hex wrench included in your package, turning the windage adjustment hex screw clock-
wise will move the laser point to the left. While turning the hex screw counter-clockwise will move your
laser point to the right.
ELEVATION
Using the small hex wrench included in your package, turning the elevation adjustment hex screw clock-
wise will move the laser point down. While turning the hex screw counter-clockwise will move your point
of impact up.
Note that the adjustments are very sensitive. One half rotation, 180 degrees, will provide approximately
10 inches of movement at 25 yards. After adjustment, carefully fire three more shots, make additional
adjustments as necessary.
Specifications
Output Power Class IIIa <5mW
Remote Pressure
Switch
10” in Length
Wavelength 635- 655 Tube Size 19mm
Dot Size .35” @ 10yds Length (Laser Only) 2.75 in.
Visible Range
Daytime – 25yds
Nightime – 100
Batteries Two LR44 Lithium Batteries
Windage/Elevation
Ajustment
+/- 10ft. @ 100 yards
LIMITED LIFETIME WARRANTY ON CENTERPOINT PRODUCTS
Your CenterPoint™ product is warranted to be free of defects in materials and workmanship for the
lifetime of the original owner. This warranty does not cover damages due to fair wear and tear, failure
to provide routine maintenance, and does not include batteries or accessories. This warranty lasts as
long as the original purchaser owns the product, and is not transferable. In the event of a defect under
this warranty, we will, at our option, repair or replace the product provided our inspection indicates
that an original defect exists. CenterPoint reserves the right to replace any product which is no longer
available with a product of comparable value and function. If CenterPoint determines the repair is not
covered under the warranty guidelines, there could be a charge to you for the repair. This is a limited
warranty and does not cover damages caused by misuse, improper handling or installation or mainte-
nance provided by someone other than CenterPoint.
This limited warranty does not include consequential damages, incidental damages, or incidental
expenses, including damage to property or any other expense. CenterPoint disclaims any implied war-
ranties. Some states do not allow the exclusion or limitation of incidental or consequential damages,
or allow limitations on implied warranties so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state and country to country.
WARRANTY CLAIMS/ REPAIR SERVICE
If your product needs repair, call CenterPoint Customer Service at 1-800-726-1122 or visit our web
site at www.centerpointoptics.com DO NOT ATTEMPT TO DISASSEMBLE IT! Any disassembly or
modification not performed by CenterPoint Precision Optics will void the warranty.
USA Customers: Please contact CenterPoint before shipping your product. Include with product
your name, address, description of problem, phone number and copies of sales receipt and warranty.
A check or money order in the amount of $10.00 to cover the cost of postage and handling is also
required. Package and return to CenterPoint, Crosman Corporation, 7629 Rts. 5 & 20, Bloomfield, NY
14469. CenterPoint will not assume any responsibility for any loss or damage incurred in shipping.
International Customers: Please return product to your nearest distributor. If you do not know your
distributor, please call 585-657-6161 and ask for our International Department for assistance. Ship-
ping and handling costs may apply.