Interlogix SuperBus 2000 2X20 - Manual (Page 5)

Additional Touchpads
1. Verify that all wiring between the panel and touchpad is
correct.
2. Check the unit number DIP switches on other bus devices
(ESM, HIM, etc.) and make a note of their respective unit
numbers.
3. Connect the panel battery and plug in the panel
transformer. Alphanumeric touchpads show “SCANNING
BUS DEVICES,” then a date and time display.
4. At a touchpad, press and hold the D and 6 buttons
(together) for at least 2 seconds. The display should show
DA n, where n is the current unit number (000 –015) for
the touchpad.
Note: At this time, the touchpad is in configuration mode
and no longer communicating with the panel. The system
may immediately indicate a bus failure. Ignore the failure
and continue with the procedure. The failure will clear after
the unit number has been successfully changed.
5. Press #. The display shows ENTER _.
6. Enter an unused three digit unit number (000 – 015), then
press #. The display shows DA n, where n is the new unit
number for the touchpad.
7. Press * to exit from the configuration mode.
8. Repeat steps 4–8 for all connected alphanumeric
touchpads.
Note: If the new unit number for the touchpad was
previously added (learned) by the panel, communication
between the touchpad and the panel begins immediately.
However, if the new unit number for the touchpad has
never been added (learned) by the panel, continue with
step nine.
9. Force the panel to scan bus devices.
• For systems where this is the only installed touchpad,
remove the panel AC power and backup battery power,
then re-apply power.
• For systems with more than one touchpad, go to another
system touchpad and enter 8 + installer CODE (default =
4321) + 0 + 1. The display shows SCANNING BUS
DEVICES, then a date and time display.
1. 10. Exit the program mode. The touchpad and all other
bus devices should operate correctly and any bus failures
should be cleared.
Note: If the panel still indicates a bus failure the panel may
have previously learned a unit number that is no longer
used by any bus device. Delete the unused unit number.
11. Verify correct operation by pressing *. The display should
show the current system status.
Note: If after pressing * the touchpad does not display the
current system status, see “Troubleshooting.”
Powering Up Advent Panels
New Installations
1. Verify that all wiring between the panel and touchpad is
correct.
2. Connect the panel battery and plug in the panel
transformer. The alphanumeric touchpad should display
“Security is Off,” or any other programmed text.
Note: If the touchpad does not display anything or
displays, “Touchpad Not Enrolled,” see “Troubleshooting.”
Existing Installations
1. Verify that all wiring between the panel and touchpad is
correct.
2. Connect the panel battery and plug in the panel
transformer.
3. At an existing touchpad, press 8 to select SYSTEM
MENU.
4. Press 0 to select ENTER PROGRAM MODE.
5. Enter your install access CODE (0123 is default).
6. Enter item number 48001 to add bus devices. All installed
devices are automatically added (learned) into panel
memory when DEVICES ADDED is displayed.
7. Press * once to exit program mode.
8. New alphanumeric touchpads should display “Security is
Off,” while existing touchpads will display custom or
programmed text.
Note: If the touchpad does not display anything or
displays, “Touchpad Not Enrolled,” see “Troubleshooting.”
Powering Up UltraGard Panels
First Touchpad
1. Disconnect all bus device wiring from the panel except for
the touchpad location closest to the panel.
2. Verify that all wiring at the panel and touchpad wiring
harness is correct.
3. With the panel power switch off, connect the panel battery
and plug in the panel AC power transformer.
4. Set the panel RUN/PROGRAM switch to RUN.
SuperBus 2000 2X20 LCD Alphanumeric Touchpad Installation Instructions 5