Novak Brushed Motor: Rock Star Motor (55-3557-1 Rev.C) User Manual

Novak r/c, inc, Precautions, Motor maintenance

Advertising
background image

#55-3557-1 Rev.C

Printed 4-2014

#55-3557-1 Rev.C

Printed 4-2014

PRECAUTIONS

PRECAUTIONS

• WATER & ELECTRONICS DON’T MIX Never allow water, moisture, or

other foreign materials to get inside motor, or on PCBs.

• CHECK MOTOR SCREWS Remember to check all motor screws

for loosening after a few runs of the motor.

• INSULATE WIRES Always insulate exposed wiring with heat shrink

tubing to prevent short circuits.

• NO SOLVENTS Do NOT expose the motor to any type of solvents.
• MOTOR CAPACITORS Brush motors generate electrical noise. Use

all 3 capacitors on the motor to help prevent radio interference.

• NO SCHOTTKY DIODES WITH REVERSIBLE ESCs NEVER use Schottky

diodes on the motor with reversible ESCs--ESC damage will occur.

• SET GEAR MESH PROPERLY Too tight of a gear mesh can result

in motor pinion shaft breakage--be sure to adjust mesh properly.

• WATER & ELECTRONICS DON’T MIX Never allow water, moisture, or

other foreign materials to get inside motor, or on PCBs.

• CHECK MOTOR SCREWS Remember to check all motor screws

for loosening after a few runs of the motor.

• INSULATE WIRES Always insulate exposed wiring with heat shrink

tubing to prevent short circuits.

• NO SOLVENTS Do NOT expose the motor to any type of solvents.
• MOTOR CAPACITORS Brush motors generate electrical noise. Use

all 3 capacitors on the motor to help prevent radio interference.

• NO SCHOTTKY DIODES WITH REVERSIBLE ESCs NEVER use Schottky

diodes on the motor with reversible ESCs--ESC damage will occur.

• SET GEAR MESH PROPERLY Too tight of a gear mesh can result

in motor pinion shaft breakage--be sure to adjust mesh properly.

MOTOR MAINTENANCE

MOTOR MAINTENANCE

• CHECK MOTOR SCREWS

Check all motor screws for loosening at regular intervals, just like

other hardware on your vehicle.

• CHECK MOTOR BEARING & BRUSH WEAR

After extensive use, your motor’s bearings or commutation brushes

may need replacement. A small drop of light oil on the bearings

periodically can help extend bearing life--however, too much oil will

attract dirt and will cause problems, so apply sparingly & wipe clean.

• CLEAN INSIDE MOTOR

Periodically remove the end bell of your motor, remove the rotor,

and blow out the inside of the motor with compressed air. Be sure

not to lose any small shim washers that may be on the shaft ends &

keep them in the correct location.

• CHECK MOTOR SCREWS

Check all motor screws for loosening at regular intervals, just like

other hardware on your vehicle.

• CHECK MOTOR BEARING & BRUSH WEAR

After extensive use, your motor’s bearings or commutation brushes

may need replacement. A small drop of light oil on the bearings

periodically can help extend bearing life--however, too much oil will

attract dirt and will cause problems, so apply sparingly & wipe clean.

• CLEAN INSIDE MOTOR

Periodically remove the end bell of your motor, remove the rotor,

and blow out the inside of the motor with compressed air. Be sure

not to lose any small shim washers that may be on the shaft ends &

keep them in the correct location.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

1. CHECK MOTOR SCREW LENGTH & INSTALL MOTOR

• Insert the M3 motor mounting screws that came with your

vehicle through the motor mounting plate.

You need no more

than 1/8” of screw extending past the vehicle’s mounting plate

(2-4mm)--Too little can strip the motor’s threads, too much may

cause internal motor damage & will void warranty.

• Attach motor to vehicle’s motor mount using one of the sets of

threaded mounting holes--

select a mounting position that keeps the

wire tabs clear of conductive surfaces like aluminum or graphite.

2. INSTALL PINION GEAR

Install pinion on motor and align pinion and spur gears. Tighten

pinion’s set screw on the flat of motor shaft.

3. ADJUST MOTOR FOR PROPER GEAR MESH

• Adjust the motor position for proper amount of free play. You

NEED a small amount of play between the pinion gear and

the spur gear (about the thickness of piece of paper)--check the

free play at several positions around the spur gear to ensure

a proper mesh

(just in case the gears are out of round).

MAKE SURE THE PINION/SPUR GEAR MESH IS NOT TOO TIGHT!

If gear mesh is too tight, motor shaft breakage can occur.

• Tighten motor mounting screws--Avoid using excessive force

that could break screws or strip the threaded holes in motor.

4. SOLDER MOTOR POWER WIRES

• Determine the best routing in vehicle for power wires. Prepare

ends of motor power wires by stripping 1/8-1/4” of insulation

from end of wire. Tin wire ends with solder.

Lay tinned end of the wire flat on the solder tab and solder

wires to proper tabs of the motor. Apply heat with soldering

iron to the power wire and solder tab--begin adding solder to

tip of iron and to wire--

Add just enough solder to form a clean

& continuous joint from the solder tab up onto the wire.

1. CHECK MOTOR SCREW LENGTH & INSTALL MOTOR

• Insert the M3 motor mounting screws that came with your

vehicle through the motor mounting plate.

You need no more

than 1/8” of screw extending past the vehicle’s mounting plate

(2-4mm)--Too little can strip the motor’s threads, too much may

cause internal motor damage & will void warranty.

• Attach motor to vehicle’s motor mount using one of the sets of

threaded mounting holes--

select a mounting position that keeps

the wire tabs clear of conductive surfaces like aluminum or graphite.

2. INSTALL PINION GEAR

Install pinion on motor and align pinion and spur gears. Tighten

pinion’s set screw on the flat of motor shaft.

3. ADJUST MOTOR FOR PROPER GEAR MESH

• Adjust the motor position for proper amount of free play. You

NEED a small amount of play between the pinion gear and

the spur gear (about the thickness of piece of paper)--check the

free play at several positions around the spur gear to ensure

a proper mesh

(just in case the gears are out of round).

MAKE SURE THE PINION/SPUR GEAR MESH IS NOT TOO TIGHT!

If gear mesh is too tight, motor shaft breakage can occur.

• Tighten motor mounting screws--Avoid using excessive force

that could break screws or strip the threaded holes in motor.

4. SOLDER MOTOR POWER WIRES

• Determine the best routing in vehicle for power wires. Prepare

ends of motor power wires by stripping 1/8-1/4” of insulation

from end of wire. Tin wire ends with solder.

Lay tinned end of the wire flat on the solder tab and solder

wires to proper tabs of the motor. Apply heat with soldering

iron to the power wire and solder tab--begin adding solder to

tip of iron and to wire--

Add just enough solder to form a clean

& continuous joint from the solder tab up onto the wire.

5512 12GA Super-Flex Wire--Black, Red, & Blue--3 ft each color, silicone.
5514 14GA Super-Flex Wire--Black, Red, & Blue--3 ft each color, silicone.
5516 16GA Super-Flex Wire--Black, Red, & Blue--3 ft each color, silicone.
5626 Glitch Buster Capacitor--Stores battery power for receiver to eliminate radio cut-out.
5647 Black Cooling Fan--25x25x10mm--All purpose cooling fan with 2-pin JST connector.
5651 Black Cooling Fan--25x25x10mm--Cooling fan 2-Pack with 2-pin JST connector.
5731 Power Connectors--3.5mm--5 pair--Gold-plated low-loss connectors. Includes heat shrink.
5741 Power Connectors--4mm--5 pair--Gold-plated low-loss connectors. Includes heat shrink.
5831 Lead-Free 3% Silver Solder--6gr--Low-resistance, high-conductivity solder.
5832 Lead-Free 3% Silver Solder--15gr Tube--Low-resistance, high-conductivity solder.
5836 Heavy Duty Lead-Free 3% Silver Solder--25gr Tube--Thicker 1.5mm solder.
5840 Double-Sided Mounting Tape--10pcs--1”x1” high-performance clear mounting tape.
5842 Double-Sided Mounting Tape--25pcs--1”x1” high-performance clear mounting tape.
5841 Double-Sided Mounting Tape--100pcs--1”x1” high-performance clear mounting tape.
5850 Heat Shrink Tubing Assortment--6pcs--6” pieces in 6 sizes from 1/16-3/8”--Black.
5851 Heat Shrink Tubing Assortment--24pcs--6” pieces in 6 sizes from 1/16-3/8”--Black.
5852 Heat Shrink Tubing Pre-Cut--40pcs--1” pieces in 1/4” size--20 each of Red & Black.
5853 Heat Shrink Tubing Box Set--160pcs--4” pieces in 6 sizes from 1/16-3/8”--Black.
5861 Pro Solder Flux--10ml--Liquid rosin flux for easy soldering of lead-free solders--Dropper bottle.

5512 12GA Super-Flex Wire--Black, Red, & Blue--3 ft each color, silicone.
5514 14GA Super-Flex Wire--Black, Red, & Blue--3 ft each color, silicone.
5516 16GA Super-Flex Wire--Black, Red, & Blue--3 ft each color, silicone.
5626 Glitch Buster Capacitor--Stores battery power for receiver to eliminate radio cut-out.
5647 Black Cooling Fan--25x25x10mm--All purpose cooling fan with 2-pin JST connector.
5651 Black Cooling Fan--25x25x10mm--Cooling fan 2-Pack with 2-pin JST connector.
5731 Power Connectors--3.5mm--5 pair--Gold-plated low-loss connectors. Includes heat shrink.
5741 Power Connectors--4mm--5 pair--Gold-plated low-loss connectors. Includes heat shrink.
5831 Lead-Free 3% Silver Solder--6gr--Low-resistance, high-conductivity solder.
5832 Lead-Free 3% Silver Solder--15gr Tube--Low-resistance, high-conductivity solder.
5836 Heavy Duty Lead-Free 3% Silver Solder--25gr Tube--Thicker 1.5mm solder.
5840 Double-Sided Mounting Tape--10pcs--1”x1” high-performance clear mounting tape.
5842 Double-Sided Mounting Tape--25pcs--1”x1” high-performance clear mounting tape.
5841 Double-Sided Mounting Tape--100pcs--1”x1” high-performance clear mounting tape.
5850 Heat Shrink Tubing Assortment--6pcs--6” pieces in 6 sizes from 1/16-3/8”--Black.
5851 Heat Shrink Tubing Assortment--24pcs--6” pieces in 6 sizes from 1/16-3/8”--Black.
5852 Heat Shrink Tubing Pre-Cut--40pcs--1” pieces in 1/4” size--20 each of Red & Black.
5853 Heat Shrink Tubing Box Set--160pcs--4” pieces in 6 sizes from 1/16-3/8”--Black.
5861 Pro Solder Flux--10ml--Liquid rosin flux for easy soldering of lead-free solders--Dropper bottle.

ACCESSORIES

ACCESSORIES

PRODUCT WARRANTY

Novak products are guaranteed to be free from defects in materials or work-

manship for a period of 120 days from the original date of purchase (verified

by dated, itemized sales receipt). Warranty does not cover incorrect installation,

components worn by use, cross-connection of battery/motor power wires,

overheating solder tabs, damage resulting from overload, wear or damage

from improper gear mesh, damage from disassembling motor or incorrect

re-assembly of motor, tampering with motor, allowing water, moisture, or any

other foreign material to enter motor, allowing exposed wiring or solder tabs

to short-circuit, or any damage caused by a crash, flooding, or act of God. In

no case shall our liability exceed the product’s original cost. We reserve the

right to modify warranty provisions without notice.
Because Novak R/C, Inc. has no control over the connection & use of motor

or other related electronics, no liability may be assumed nor will be accepted

for damage resulting from the use of this product. Every motor is tested before

leaving our facility and is, therefore, considered operational.
By the act of connecting the motor to speed control or operating motor, the user

accepts all resulting liability.

Novak R/C, Inc.

19 Rancho Circle

Lake Forest, CA 92630

(949) 916-6044 • Monday-Thursday

e-mail:

[email protected]

web:

www.teamnovak.com

©2014 Novak R/C, Inc. California, U.S.A. • All Rights Reserved

No part of these instructions may be reproduced without the

written permission of Novak R/C, Inc. Motor made in Japan and

tested at the Novak facility in Lake Forest, CA.

PRODUCT WARRANTY

Novak products are guaranteed to be free from defects in materials or work-

manship for a period of 120 days from the original date of purchase (verified

by dated, itemized sales receipt). Warranty does not cover incorrect installation,

components worn by use, cross-connection of battery/motor power wires,

overheating solder tabs, damage resulting from overload, wear or damage

from improper gear mesh, damage from disassembling motor or incorrect

re-assembly of motor, tampering with motor, allowing water, moisture, or any

other foreign material to enter motor, allowing exposed wiring or solder tabs

to short-circuit, or any damage caused by a crash, flooding, or act of God. In

no case shall our liability exceed the product’s original cost. We reserve the

right to modify warranty provisions without notice.
Because Novak R/C, Inc. has no control over the connection & use of motor

or other related electronics, no liability may be assumed nor will be accepted

for damage resulting from the use of this product. Every motor is tested before

leaving our facility and is, therefore, considered operational.
By the act of connecting the motor to speed control or operating motor, the user

accepts all resulting liability.

Novak R/C, Inc.

19 Rancho Circle

Lake Forest, CA 92630

(949) 916-6044 • Monday-Thursday

e-mail:

[email protected]

web:

www.teamnovak.com

©2014 Novak R/C, Inc. California, U.S.A. • All Rights Reserved

No part of these instructions may be reproduced without the

written permission of Novak R/C, Inc. Motor made in Japan and

tested at the Novak facility in Lake Forest, CA.

Advertising