Novak 55-5750-1.2_Manufacturing 9-Up Layout (55-5750-1.2) - Manual

NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector (“+” & “–” are marked on the side of connector). Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint. If needed, add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector (“+” & “–” are marked on the side of connector). Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint. If needed, add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector (“+” & “–” are marked on the side of connector). Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint. If needed, add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector (“+” & “–” are marked on the side of connector). Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint. If needed, add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector (“+” & “–” are marked on the side of connector). Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint. If needed, add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector (“+” & “–” are marked on the side of connector). Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint. If needed, add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector (“+” & “–” are marked on the side of connector). Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint. If needed, add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector (“+” & “–” are marked on the side of connector). Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint. If needed, add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
NOVAK POWER CONNECTORS
Low-Loss • Polarized • Gold-Plated
For best results, strip, twist, & pre-tin about 1/4” of your
16-12G power wires before soldering to the connector.
To avoid over-heating connector’s plastic, plug into a mating/opposite-
end connector (not on a battery pack) to help dissipate extra heat.
Insert the stripped & tinned end of the wire into the correct barrel
of the connector (“+” & “–” are marked on the side of connector). Heat
the tinned wire end with a good quality, high-power soldering iron
until the solder reflows into the connector’s barrel forming a clean
and continuous solder joint. If needed, add a small amount of extra
solder--again, being careful not to over-heat the connector’s plastic.
Slide the included heat shrink tubing over the wires and shrink over
the connector’s exposed barrel and the solder joint.
©Novak R/C, Inc. All Rights Reserved • 2-2014 • 55-5750-1.2
(949) 916-6044 • Monday-Thursday
e-mail: [email protected]
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com
www.teamnovak.com