Rev-A-Shelf 4WH-RM-15DM-1 User Manual

Alternative “easy install, Door mounting brackets tape, Door

Advertising

Step 6. Add Dimension A and B together. Measure this distance from

bottom of the inside cabinet door and mark a horizontal line.

(See figure 4)

Due to the many different door styles, overlays, and cabinet constructions, the Rev-A-Shelf door mount brackets provide the ultimate in flexibility for

ensuring that the positioning of the hole pattern on the door bracket installs with the thick portion of any cabinet door frame. Thus, eliminating any need

for adding a sub door panel.

Step 7. Take Dimension C from Step 4 and divide it by two. Measure this

distance to the left of the center point on the inside of the cabinet door

and make a vertical line. Measure this distance to the right of the center

point on the inside of the cabinet door and make another vertical line.

(See figure 5)

Step 7

Take Dimension C (from Step 4)
and divide it by two. Measure this
distance to the left of the center point
on the inside of the cabinet door and make a
vertical line. Measure this
distance to the right of the center
point on the inside of the cabinet
door and make another vertical line
(See illustration 6)

Step 8

Remove Door Brackets from product
members and screw to inside of cabinet
door with #6 x 1/2'' flat head screws.
NOTE: Line up door bracket to cabinet door
by aligning door bracket with the vertical and
horizontal lines you have marked in Steps 6
& 7.
(See illustration7)

Step 9

Hang door with brackets attached on
the mounting screws on to the product
members. Tighten bottom screws
securly. Tighten top screws (with
washer) snugly allowing for future
adjustment.
(See illustration 8)

Step 6

Add Dimension A and Dimension B
together. Measure this distance from
bottom of the inside of your cabinet
door and mark a horizontal line.
(See illustration 5). Measure center
point on inside of cabinet door and mark
this point as well.

A+B

Center

Dimension C

Equal

Step 10.

Be sure bumper pads are installed to all four
corners of door. Push door closed and apply
pressure to all four
corners making sure
door is flush with cabinet.
(See illustration 9).

Step 11.

Pulling from bottom,
pull door open.
(See illustration 10).
Securly tighten
top screws.

Step 12.

If your cabinet door is not straight
(even all around) you can adjust it
by loosing the screws on one of the
sides, properly align the cabinet
door and re-tighten the screws.

Helpful Hints:

There are several different

ways to mount the Door

Brackets to your cabinet

door ensuring that you

are mounting to the

thick portion of the door.

For instance, spacers can

be used when mounting Door Brackets to the

Product Members (spacer kit included). The Door

Bracket can also be installed on the inner side of the

Product Member.

Illustration 5

illustration 8

illustration 6

ilustration 7

If your door is parallel but slightly
off center. Loosen screws
that attach the slide mounting feet
to the cabinet floor, slide assembly
sideways as needed and re-tighten
screws.

2409 Plantside Drive

Jeffersontown, KY 40299

800-626-1126

502-491-2215 fax

illustration 9

illustration 10

Door...

off left

to right

Door...

crooked

all around

Door...

straight

after

ajustment

Door...

straight

after

ajustment

Door

I-RV-DM KIT

Step 5. Measure the distance from the bottom face frame to the bottom

of the door mount bracket, Noted as Dimension A. Measure your door

overlap. Noted as Dimension B as shown in figure 3. NOTE: On

frameless cabinets, measure from the cabinet floor to the bottom of the

door bracket.

Installing Door Mount Brackets on Cabinet Door

Mounting

Instructions

Step 1. Remove left and right door mount brackets. Leave product

member attached.

Step 2. Remove cabinet door and hinges. Place the product inside

cabinet. NOTE: If a rear wood bin is included, remove for installation.

Step 3. Center the wood frame left to right in the opening.

Position the front of the wood frame even with the front of the face frame

as shown in figure 1. Attach to bottom of cabinet using (5) #8 x 5/8” pan

head screws (included). (See figure 1)

Step 4. Re-install door mount brackets as shown in figure 2. Measure

outside to outside dimension of door brackets. This is Dimension C.

Step 7

Step 8

Step 9

Step 6

A+B

Center

Dimension C

Equal

Step 10.

Be sure bumper pads are installed to all four
corners of door. Push door closed and apply
pressure to all four
corners making sure
door is flush with cabinet.
(See illustration 9).

Step 11.

Pulling from bottom,
pull door open.
(See illustration 10).
Securly tighten
top screws.

Step 12.

If your cabinet door is not straight
(even all around) you can adjust it
by loosing the screws on one of the
sides, properly align the cabinet
door and re-tighten the screws.

Helpful Hints:

There are several different

ways to mount the Door

Brackets to your cabinet

door ensuring that you

are mounting to the

thick portion of the door.

For instance, spacers can

be used when mounting Door Brackets to the

Product Members (spacer kit included). The Door

Bracket can also be installed on the inner side of the

Product Member.

Illustration 5

illustration 8

illustration 6

ilustration 7

If your door is parallel but slightly
off center. Loosen screws
that attach the slide mounting feet
to the cabinet floor, slide assembly
sideways as needed and re-tighten
screws.

2409 Plantside Drive

Jeffersontown, KY 40299

800-626-1126

502-491-2215 fax

illustration 9

illustration 10

Door...

off left

to right

Door...

crooked

all around

Door...

straight

after

ajustment

Door...

straight

after

ajustment

Door

I-RV-DM KIT

Face Frame

Mounting hole

locations

Dimension C

fig. 5

fig. 4

fig. 1

fig. 2

Face Frame

fig. 3

Door

Cabinet

Floor

Dimension

Paso 10: Asegúrese de instalar topes de amortiguación (no incluidos) en las cuatro

esquinas de la puerta. Cierre la puerta y presione las cuatro esquinas para

asegurarse de que la puerta esté a ras con el armario. (Ver la ilustración 8)

Étape 10: Veiller à ce que les quatre coins de la porte soient munis de coussinets

amortisseurs (non fournis). Fermer la porte et appuyer fermement sur les quatre

coins pour assurer que la porte est à affleurement de l’armoire. (Voir l’illustration 8)

Paso 11: Tire de la puerta por los costados y a la altura de las deslizaderas

para abrirla. (Ver la ilustración 9) Apriete bien los tornillos superiores.

Étape 11: Ouvrir la porte en tirant sur les côtés au niveau des glissières.

(Voir l’illustration 9). Bien serrer les vis du haut.

Paso 12: Para ajustar la puerta del armario si no está derecha

(emparejarla a todo su alrededor), debe aflojar los tornillos en uno de los lados,

alinear bien la puerta y volver a apretar los tornillos.

Étape 12: Si la porte de l’armoire est de travers, desserrer les vis d’un côté, corriger

l’alignement de la porte et resserrer les vis.

Si la puerta está paralela pero ligeramente descentrada, afloje los tornillos que

sujetan las patas de las deslizaderas al piso del armario, mueva el ensamblaje lat-

eralmente según sea necesario y vuelva a apretar los tornillos.

Si la porte est parallèle mais légèrement décentrée, desserrer les vis fixant les pattes

de l’ensemble de glissières au fond de l’armoire. Glisser l’ensemble vers le côté

jusqu’à ce que la position soit correcte et resserrer les vis.

Paso 9: Monte la puerta con los soportes instalados en los tornillos de

montaje en las placas del producto. Apriete bien los

tornillos de la parte inferior. Apriete los tornillos superiores (con las

arandelas) pero de modo que le permite realizar ajustes más adelante.

(Ver la ilustración 7)

Étape 9: Suspendre la porte avec les

supports aux vis de montage du produit. Fermement serrer les vis du

bas. Bien serrer les vis du haut (avec les rondelles) en

laissant un peu de jeu pour des réglages futurs. (Voir l’illustration 7)

12400 Earl Jones Way • Louisville, KY 40299

(800) 626-1126 • www.rev-a-shelf.com

Paso 8: Retire los soportes de puerta de las placas del producto y atorníllelos en

el interior de la puerta del armario con tornillos de cabeza plana núm. 6 x 1/2 pulg.

Nota: Coloque los soportes de puerta sobre las líneas verticales y horizontales que

ha dibujado en los pasos 2 y 3 para alinearlos. (Ver la ilustración 6)

Étape 8: Enlever les supports de porte du produit et visser sur l’intérieur de la

porte d’armoire avec des vis à tête plate no 6 x 1/2 po. REMARQUE. Aligner le

support de porte sur la porte en l’alignant sur les lignes verticale et horizontale

tirées aux étapes 2 et 3. (Voir l’illustration 6)

Step 7

Step 8

Step 9

Step 6

A+B

Center

Dimension C

Equal

Step 10.

Be sure bumper pads are installed to all four
corners of door. Push door closed and apply
pressure to all four
corners making sure
door is flush with cabinet.
(See illustration 9).

Step 11.

Pulling from bottom,
pull door open.
(See illustration 10).
Securly tighten
top screws.

Step 12.

If your cabinet door is not straight
(even all around) you can adjust it
by loosing the screws on one of the
sides, properly align the cabinet
door and re-tighten the screws.

Helpful Hints:

There are several different

ways to mount the Door

Brackets to your cabinet

door ensuring that you

are mounting to the

thick portion of the door.

For instance, spacers can

be used when mounting Door Brackets to the

Product Members (spacer kit included). The Door

Bracket can also be installed on the inner side of the

Product Member.

Illustration 5

illustration 8

illustration 6

ilustration 7

If your door is parallel but slightly
off center. Loosen screws
that attach the slide mounting feet
to the cabinet floor, slide assembly
sideways as needed and re-tighten
screws.

2409 Plantside Drive

Jeffersontown, KY 40299

800-626-1126

502-491-2215 fax

illustration 9

illustration 10

Door...

off left

to right

Door...

crooked

all around

Door...

straight

after

ajustment

Door...

straight

after

ajustment

Door

I-RV-DM KIT

STEP 5:

Peel off the exterior layer of tape.

Now carefully line up your desired

door position by eyesight using

the drawer above and any cabinets

to your left or right as a gauge for

correct alignment.

STEP 6:

Press the door firmly onto the

door brackets with the two sided

tape. Put pressure directly on the

lower left and right edge to allow

for good adhesion.

ALTERNATIVE “EASY INSTALL”

for RV Series Pull-Out Waste Containers WITH

Door Mounting Brackets Tape

Your Door Mount Kit also includes two pieces of specially designed two-sided tape. Follow the directions below for quick and easy installation

method that is usually much faster for “In-Home” retro-fitting:

STEP 1:

Follow steps one through four on “Installation

Instructions” (Seperate Sheet).

STEP 3:

Peel off one side of each of the (4) tape squares provided and

carefully place over the door bracket flanges

STEP 2:

Make sure you have correctly

selected the correct positioning of

our Door Bracket Flanges so that

the mounting holes will be located

in a position to insert the fastners

(screws) in the thick, outside

section of the door panel.

STEP 4:

Loosen the 4 bolts (2 each side) that connect the door brackets to

the product member bracket. Pull them forward (towards you) and

tighten them. This will insure that the face of the door bracket

extends slightly outside of the front frame of your cabinet.

STEP 9:

• Final adjustment

• Loosen the four bolts and make adjustments if necessary.

(See Step 12 on installation instructions)

STEP 7:

Carefully pull out door from bottom edge and mark

several holes on each side through the brackets.

STEP 8:

Fasten the brackets to the door

using the tape as a temporary hold

while you insert your #6 x 1/2"

wood screws.

2409 Plantside Drive • Jeffersontown, KY 40299

800-626-1126 • 502-491-2215 fax

www.rev-a-shelf.com

I-RV-DM-KIT-E 4-02

fig. 6

fig. 7

fig. 9

fig. 8

I-4WBM-RM

02/09

Paso 7: Tome la Dimensión C del Paso 4 y divídala entre 2. Mida esta

distancia a la izquierda del punto central en el interior de la puerta de

gabinete y haga una línea vertical. Mida esta distancia a la derecha del

punto central en el interior de la puerta del gabinete y haga otra línea

vertical. (Ver figura 5)

Étape 7. Prenez la dimension C de l’étape 4 et divisez-la par deux.

Mesurez cette distance à la gauche du point central sur l’intérieur de la

porte du caisson et marquez une ligne verticale. Mesurez cette distance

à la droite du point central sur l’intérieur de la porte de coffret et

marquez une autre ligne verticale. (Voir la figure 5)

Step 7

Step 8

Step 9

Step 6

A+B

Center

Dimension C

Equal

Step 10.

Be sure bumper pads are installed to all four
corners of door. Push door closed and apply
pressure to all four
corners making sure
door is flush with cabinet.
(See illustration 9).

Step 11.

Pulling from bottom,
pull door open.
(See illustration 10).
Securly tighten
top screws.

Step 12.

If your cabinet door is not straight
(even all around) you can adjust it
by loosing the screws on one of the
sides, properly align the cabinet
door and re-tighten the screws.

Helpful Hints:

There are several different

ways to mount the Door

Brackets to your cabinet

door ensuring that you

are mounting to the

thick portion of the door.

For instance, spacers can

be used when mounting Door Brackets to the

Product Members (spacer kit included). The Door

Bracket can also be installed on the inner side of the

Product Member.

Illustration 5

illustration 8

illustration 6

ilustration 7

If your door is parallel but slightly
off center. Loosen screws
that attach the slide mounting feet
to the cabinet floor, slide assembly
sideways as needed and re-tighten
screws.

2409 Plantside Drive

Jeffersontown, KY 40299

800-626-1126

502-491-2215 fax

illustration 9

illustration 10

Door...

off left

to right

Door...

crooked

all around

Door...

straight

after

ajustment

Door...

straight

after

ajustment

Door

I-RV-DM KIT

fig. 5

Puerta

Porte

Dimensión C

Door Mount

Bracket

Product

Member

Advertising

Popular Brands

Popular manuals