SINGER 147-81 - Manual (Page 8)

14
PARTS FOR MACHINE No, 147-80
No. Plate
190J 20696
32062 20696
131413 20696
50470J 20696
131421 20696
207J 20696
7071 20696
131422 20696
207J 20696
7071 20696
131493 20706
190J 20706
131494 20706
223J 20706
131495 20706
131496 20706
997J 20706
38486 20707
46059 20708
742F 20707
*15404 —
15405 —
Name
Thread (under) Take-up Stripper Plate
Screw (3)........................
Thread (under) Take-up Stripper Washer..
" " '' Thread Guard
(fibre)..........................
Thread (under) Take-up Thread Guard
Screw (2)........................
Thread (under) Take-up Thread Guide
(left)...........................
Thread (under) Take-up Thread Guide
(left) Screw.....................
Thread (under) Take-up Thread Guide
(left) Screw Washer..............
Thread (under) Take-up Thread Guide
(right)..........................
Thread (under) Take-up Thread Guide
(right) Screw....................
Thread (under) Take-up Thread Guide
(right) Screw Washer.............
Thread (upper) Eyelet................
" " " Screw.............
" ” Take-up with 223J........
" " " Clamping Screw...
" " (auxiliary)......
" " ” " Clamp
tt If If II II
Screw............................
Throat Plate for 54177...............
.......... 131544 and 131545.....
" " Screw (2).................
Trade Mark...........................
" " Rivet (2)..................
15
MACHINE No. 147-81
FOR MEDIUM WEIGHT FABRICS. ONE NEEDLE,
ONE LOOPER. LENGTH OF STITCH 7 TO 25 TO
THE INCH. NEEDLE BAR STROKE I 7/32 INCHES.
BALL BEARING. SPEED 4000 R. P. M.
NOTE: THIS MACHINE IS THE SAME AS THE 147-80
MACHINE, WITH THE FOLLOWING EXCEPTIONS:
No. Plate Name
131072 20697 Arm Rock Shaft Crank, back (ball bearing,
solid) with two 50083AL, In place of
131343............................
131485 .... Arm Rotary Shaft 131476 with 640E,68459,
131111 and 131502, In place of
131477............................
66459 ---- Crank Connecting Rod 131471 with 131072,
In place of 131484................
*131110 20699 Looper Driving Shaft and Feed Lifting
Eccentric, In place of 68481......
Note: When No. 131110 Is required for repairs, the
Arm Rotary Shaft must be returned to the factory
to be adjusted to the new part.
*131111 ---- Looper Driving Shaft and Feed Lifting
Eccentric 131110 with 54027, 54227,
54228 and 68479, In place of 68482..
54036 20701 Needle Bar (hollow) with 857AL, In place
of 131490.........................
131399 ---- Needle Bar Connecting Link and Thread
(upper) Controller 68488 with 68489
and 131400, In place of 131491....
131400 20701 Needle Bar Connecting Stud with 211F and
1492E, In place of 131492.........
131025 20709 Slack Thread Controller...............
54242 20709 " “ " Clamp.............
190J 20709 II " « . Screw.....
38484 20709 Thread (upper) Eyelet, In place of
131493............................
131332 20709 Thread (upper) Take-up..................
54194 20709 " " " Plate............
68164 20709 » . , , Spring......
1449J 20709 » » . и » scj-ew
131333 20709 Thread (upper) Take-up complete. Nos.
1449J, 54194, 68164 and 131332, in
place of 131494...................
211F 20701 Thread (upper) Take-up Set Screw........