Nor-Cal Intellisys Throttling Butterfly Valve - Manual (Page 13)

12 12 Visit our Web Site www.n-c.com
TBV-OP-LIT 01/04
I
NTELLISYS
T
HROTTLING
B
UTTERFLY
V
ALVES
13 Call toll free 800-824-4166 or 530-842-4457 • FAX 530-842-9130
TBV-OP-LIT 01/04
I
NTELLISYS
T
HROTTLING
B
UTTERFLY
V
ALVES
APPENDIX II.I – TBV Heater Jackets and Accessory Ordering Information
TBV
Control Type Control Temp. Operating Voltage Valve Size
PID Controller
MODEL
NUMBER ZONES
OPERATING
VOLTAGE
HC-935A-1-1 1 120 VAC
HC-935A-1-2 1 240 VAC
CONTROL
TYPE
VALVE SIZE
CODE SIZE FLANGE
CONTROL
TEMPERATURE
OPERATING
VOLTAGE
HC = PID control * 100 1.00 * NW-25 200 = All PID controlled jackets 1 = 120 VAC
HT = Thermostatic control 150 1.50 * NW-40 090 = 90ºC Thermostat 2 = 208-240 VAC
* Requires separate PID controller 200 2.00 * NW-50 120 = 120ºC Thermostat
250 2.50 ISO-63 150 = 150ºC Thermostat
300 3.00 ISO-80
400 4.00 ISO-100
600 6.00 ISO-160
800 8.00 ISO-200
* Includes two special NW clamps
Heater Jacket Part Number and Ordering Information
Use the model number tree at right with the matrix below to define
a valid Nor-Cal Products TBV heater model number.
APPENDIX II – Valve, Spare Parts, Hardware and Cable Assembly Ordering Information
Installation Hardware
TABLE A-II.IV – ISO INSTALLATION HARDWARE
MODEL
NUMBER DESCRIPTION
TBV-ISO-63-DCP ISO-63 aluminum double claw clamp with bolt
TBV-ISO-100-DCP ISO-100 aluminum double claw clamp with bolt
TBV-ISO-160-DCP ISO-160 aluminum double claw clamp with bolt
TBV-ISO-200-DCP ISO-200 aluminum double claw clamp with bolt
TBV-ISO-250-DCP ISO-250 aluminum double claw clamp with bolt
TBV-ISO-63-BOLT M8×70 SS bolt with nut and 2 washers
TBV-ISO-80-BOLT M8×70 SS bolt with nut and 2 washers
TBV-ISO-100-BOLT M8×70 SS bolt with nut and 2 washers
TBV-ISO-160-BOLT M10×100 SS bolt with nut and 2 washers
TBV-ISO-200-BOLT M10×100 SS bolt with nut and 2 washers
TBV-ISO-250-BOLT M10×100 SS bolt with nut and 2 washers
ISO-63-CR-SV ISO-63 stainless steel centering ring with Viton O-Ring
ISO-63-CR-AV ISO-63 aluminum centering ring with Viton O-Ring
ISO-80-CR-SV ISO-80 stainless steel centering ring with Viton O-Ring
ISO-80-CR-AV ISO-80 aluminum centering ring with Viton O-Ring
ISO-100-CR-SV ISO-100 stainless steel centering ring with Viton O-Ring
ISO-100-CR-AV ISO-100 aluminum centering ring with Viton O-Ring
ISO-160-CR-SV ISO-160 stainless steel centering ring with Viton O-Ring
ISO-160-CR-AV ISO-160 aluminum centering ring with Viton O-Ring
ISO-200-CR-SV ISO-200 stainless steel centering ring with Viton O-Ring
ISO-200-CR-AV ISO-200 aluminum centering ring with Viton O-Ring
ISO-250-CR-SV ISO-250 stainless steel centering ring with Viton O-Ring
ISO-250-CR-AV ISO-250 aluminum centering ring with Viton O-Ring
TABLE A-II.III – NW INSTALLATION HARDWARE
MODEL
NUMBER DESCRIPTION
NW-25-SSC NW-25 SureSeal clamp
NW-25-CP NW-25 wingnut clamp
NW-40-SSC NW-40 SureSeal clamp
NW-40-CP NW-40 wingnut clamp
NW-50-SSC NW-50 SureSeal clamp
NW-50-CP NW-50 wingnut clamp
NW-25-CR-SV NW-25 stainless steel centering ring with Viton O-Ring
NW-25-CR-AV NW-25 aluminum centering ring with Viton O-Ring
NW-40-CR-SV NW-40 stainless steel centering ring with Viton O-Ring
NW-40-CR-AV NW-40 aluminum centering ring with Viton O-Ring
NW-50-CR-SV NW-50 stainless steel centering ring with Viton O-Ring
NW-50-CR-AV NW-50 aluminum centering ring with Viton O-Ring