Denon AVR-3805 - Manual (Page 20)

20
7 SETTING UP THE SYSTEM
• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 7 to 16), make the various
settings described below on the monitor screen using the AVR-3805’s on-screen display function.
These settings are required to set up the listening room’s AV system centered around the AVR-3805.
SYSTEM SETUP button
Press this to display the system setup menu.
ENTER button
Press this to switch the display.
Also use this button to complete the setting.
CURSOR buttons
Use these to move the cursors the left, right, up and down on
the screen
• System setup items and default values (set upon shipment from the factory)
1 Check that the remote control unit set to AMP mode.
2
Use the following buttons to set up the system
• Use the following buttons to set up the system.
2. Speaker Setup
Speaker Setup Default settings
1
2
Speaker
Configuration
Channel
Level
Input the combination of speakers in your system and their
corresponding sizes (SMALL for regular speakers, LARGE for full-
size, full-range) to automatically set the composition of the signals
output from the speakers and the frequency response.
This adjusts the volume of the signals output from the speakers and
subwoofer for the different channels in order to obtain optimum
effects.
Front Sp.
Large
Center Sp.
Surround Sp.
A / B Subwoofer
Small Small Yes
Front L & R Center Surround L & R Subwoofer
12 ft (3.6 m) 12 ft (3.6 m) 10 ft (3.0 m) 12 ft (3.6 m)
Front L Front R Center
Surround
R
Surround
Back R
Subwoofer
0 dB 0 dB 0 dB 0 dB 0 dB 0 dB
Surround Back Sp.
Small / 2spkrs
3
Delay Time
This parameter is for optimizing the timing with which the audio
signals are produced from the speakers and subwoofer according to
the listening position. SBL & SBR
10 ft (3.0 m)
Surround
Back L
0 dB
Surround
L
0 dB
Crossover
Frequency
5
Set the frequency (Hz) below which the bass so of the various
speaker is to be output from the subwoofer.
(Surround
Speaker
Setting)
Use this function when using multiple surround speaker
combinations for more ideal surround sound. Once the
combinations of surround speakers to be used for the
different surround modes are preset, the surround
speakers are selected automatically according to the
surround mode. Surround
mode
Surround
speaker
DOLBY/
DTS
CINEMA
DOLBY/
DTS
MUSIC
WIDE
SCREEN
5CH/7CH
STEREO
DSP
SIMULATION
MULTI CH
MODE
EXT.IN
A A A A A A A A
4 80Hz
Subwoofer mode This selects the subwoofer speaker for playing deep bass signals. LFE
6
DOLBY/
PL IIx
GAME
1. Auto Setup/Room EQ
Auto Setup/Room EQ Default settings
1
2
Auto Setup
Room EQ
Setup
Power Amp
Assignment
This parameter is for optimizing the Room EQ with which the audio
signals are produced from the speakers.
3
Manual EQ
Setup
Direct Mode
Setup
5
Set the ON/OFF setting of Room EQ, in the case of the surround
mode is in Direct or Pure Direct.
4
Mic Input Select
Set this to switch the Mic Input jack for use for Mic or V.Aux L-
channel input jack.
Set this to switch the surround back channel’s
power amplifier for use for zone2 or zone3.
Set the Room EQ setting with All or Assign for each surround mode.
SURROUND BACK
All Channel and Frequency=0dB
All
OFF
Mic