Lenco IPD-9000 - Manual (Page 5)

GB GB
8
Radio Tuner Operation
FM Antenna
Connect an external FM antenna cable to the FM ANT connector at rear of the unit for the best FM radio
reception.
Radio Tuning
1. Press the STANDBY button to turn on the unit, where the power status indicator light on.
2. Press the FUNCTION button to select FM radio mode, you may press the MODE / ST. button from the
remote control to select FM stereo (the stereo indicator will display on LCD) or FM mono radio
receiving mode, if necessary.
3. To manually tune to a desired station, repeatedly press the TUN + / - button.
4. To automatically search for stations with strong signals, press and hold the TUN + / - button until the
frequency digits on display begins to scan then release the button. The tuner will stop on the first
strong signal it finds.
Notes:
- Manual tune to select weaker stations that might be skipped during automatic tuning.
- If the automatic tuning does not stop on the exact frequency of the station, for example, it stops on
88.9 MHz instead of 88.8 MHz, use the manual tuning method to "fine tune" to the exact frequency
of the desired station.
Radio Preset Stations
The unit allows you to store up to 20 FM stations for easy recall at any time.
Preset Stations
1. Press the STANDBY button to turn on the unit, where the power status indicator light on.
2. Press the FUNCTION button to select FM radio mode.
3. Tune to the radio station you want to store in memory by using the TUN + / - button.
4. Press the MEM button. The preset channel number appears on display and blinking.
5. To select desired preset station number, press the CH +/- button.
6. To confirm preset location, press the MEM button.
7. Repeat steps 3 to 6 to store other stations, if apply.
Notes:
1. There is a few seconds delay when programming, after this delay time, the unit will automatically
switch back to normal tuner mode.
2. You can overwrite a preset station by overwriting and storing the new frequency in its place.
Recalling Preset Station
1. Press the STANDBY button to turn on the unit, where the power status indicator light on.
2. Press the FUNCTION button to select FM radio mode.
3. From the main unit, press the PRESET button then press CH +/- button, or, directly press the CH +/-
button from the remote control. The preset channel number will appear on display.
RDS function
The unit incorporated the RDS functions, PS (programme service), TYPE (programme type) and RT (radio
text).
When the received radio station with RDS information, the LCD displays the “RDS” indicator. You may
press the RDS button repeatedly from the remote control to select one of those functions (PS, TYPE or
RT).
Listening to CD Music
The CD player can playback CD/CD-R/CD-RW disc with Audio CD and MP3 format.
CD Playback
1. Press the STANDBY button to turn on the unit.
2. Press the FUNCTION button to select CD mode.
3. A CD with printed side facing up, insert it into the CD slot.
4. The player starts music playback automatically.
5. For Audio CD format disc ----- The display will show the “CD” indicator and the track number (e.g. T001).
For MP3 file format disc ---- The display will show the “MP3” indicator, Folder number (e.g. A01) and
the track number (e.g. T001).
6. Adjust the volume level by rotating the VOLUME knob.
7. To skip to a desired CD track, press the / button or the / button from the remote
9
control. If it is playing the MP3 song, you may press the DIR +/- button from the remote control to select
a desired folder.
8. To fast-rewind or forward within the track playing, press and hold the / button, or the /
button from the remote control.
9. To pause CD playback, press the play/pause button.
To resume playback, press the play/pause button again.
10. To stop CD playback, press the STOP button.
11. To eject the CD, press the OPEN/CLOSE button.
CD Play Modes
Repeat Playback
ƽ For Audio CD disc :
To repeat playback of one track, press the P-MODE button once (from the remote control). A repeat one
indicator “ ”appears on the LCD.
To repeat playback of an entire CD, press the P-MODE button until the repeat all “ ” indicator
appears on LCD.
ƽ For MP3 disc :
To repeat playback of one track, press the P-MODE button once (from the remote control). A repeat
one indicator “ ” appears on the LCD.
To repeat playback a directory, press the P-MODE twice. A repeat directory indicator “ DIR”
appears on LCD.
To repeat playback of an entire CD, press the P-MODE button until the repeat all “ ” indicator
appears on LCD.
Random Playback
To playback CD tracks in random order, press the P-MODE button (from the remote control) until “RND”
indicator appears on the LCD.
INTRO Playback
To playback the first ten seconds of each song, press the P-MODE button (from the remote control) until “INTRO”
indicator appears on LCD.
To cancel a CD play mode, press the STOP button at any time.
CD Program Playback
This feature allows you to program up to 20 tracks for Audio CD or 30 songs for MP3 CD in a desired order.
1. With CD playback stopped, press the PGM button once from the remote control.
The LCD shows following indication: “PGM” indicator
The program number (e.g. P01) blinks.
The Track number (e.g. T001)
The Directory (Folder) number (e.g. A01) ---- apply for MP3 disc only.
2. To select a directory number, press the DIR +/- button from the remote control (for MP3 disc only).
To select a track number, press the / button from the remote control.
3. When desired track number displayed, press the PGM button to confirm entry.
4. To program up to 20 Audio CD tracks or 30 MP3 CD songs, repeat steps 2 and 3 until all desired tracks
are entered.
Or, to begin programmed playback, press the Play/Pause button, the “PGM” indicator stays on
the display.
5. To cancel programmed playback, press the STOP button twice.
Note:
ƽ If you press the / button (from the remote control) during programmed playback, the unit will
skip backward / forward to previous / next track in the program, not necessary the previous / next track
on the disc.
ƽ The CD play modes function, “ ” repeat one track and “ ” repeat all programmed track, work
in the same manner as during normal CD playback (see CD Play Modes above).
ID3 Function
This function allows users to view the song information (if any) on the track (file) that they are playing.
To enable this function:
1. During CD-MP3 playback, press the ID3 button. The information (e.g. artist name, song title) saved on
the track (file) will be shown on the LCD display.
2. To turn off the ID3 function, press the ID3 button again.
Note:
ƽ Only applicable for recorded tracks (files) with ID3.
ƽ The unit supports ID3 in English characters only. It does not support any other languages.
iPD-9000 5L IB.indd 8-9 2011-10-17 10:06:55