DR Power Tow-Behind 9.59 Premier (September 2014 - Present) - Manual (Page 10)

10 DR ® LEAF and LAWN
Power Unit Hardware (Figure 6):*
Item # Part #
Description Qty
1 ............. 35023 .............. Bolt, Hex, Flange, 5/16-18 X .75" .................. 6
2 ............. 26556 .............. Bolt, HCS, 1/2-13 X 2.75", GR5, ZP............... 2
3 ............. 33335 .............. Nut, Nylon Lock, Flange, 1/2-13 ................... 2
4 ............. 11241 .............. Washer, Flat, 5/16" USS, ZP.......................... 1
5 ............. 11243 .............. Washer, Lock, 5/16", Split, ZP ....................... 1
6 ............. 33332 .............. Nut, Nylon Lock, Flange, 5/16-18 ................. 6
Enclosure Hardware (Figure 7):*
Item # Part #
Description Qty
1 ............. 35026 .............. Bolt, C-Head, 5/16-18 X 2.5", ZP.................... 4
2 ............. 35027 .............. Bolt, C-Head, 5/16-18 X 1.75", ZP.................. 8
3 ............. 11076 .............. Nut, Nylon Lock, 5/16-18, ZP ......................... 3
4 ............. 11073 .............. Nut, Nylon Lock, 1/4-20, ZP ........................... 10
5 ............. 35023 .............. Bolt, Hex, Flange, 5/16-18 X .75 ..................... 1
6 ............. 11241 .............. Washer, Flat, 5/16 USS, ZP ............................ 2
7 ............. 27905 .............. Push Nut, 5/16" .............................................. 12
Wheel Hardware (Figure 8):*
Item # Part #
Description Qty
1 ............. 35039 .............. Washer, 1.06" ID X 2" OD X .13", ZP............. 4
2 ............. 12334 .............. Bolt, HCS, 3/8-16 X 1.75", GR5, ZP ............... 4
3 ............. 33333 .............. Nut, Nylon Lock, Flange, 3/8-16 .................... 4
4 ............. 12685 .............. Pin, Cotter, 3/16" X 1.5" ................................. 2
*Above Sets include some extra hardware.
Installing the Wheels (Use Wheel Hardware Package, see Figure 8)
Tools Needed:

Two 9/16" Wrenches

Pliers
1. Tip the Cart over to access the Frame (Figure 9).
2. Install the Axle Brackets and loosely secure with the Bolts and Locknuts
using two 9/16" Wrenches.
3. Slide the Axle through the Brackets until the same amount sticks out on the
side. Tighten the hardware.
4. For Machines with Dual Wheels: Slide a Wheel onto the end of the Axle with
the Valve Stem facing in and install a Washer against the Wheel (Figure 10).
1
Figure 6
2
3
4 6
5
1
Figure 7
2
3
4
6
5
7
1
Figure 8
2
3
4
Axle Brackets
Figure 9
Frame
Axle
Hardware
Axle
1st Dual Wheel (Valve Stem and
Grease Fitting facing in)
Figure 10
Large Washer