Fieldpiece SIG1 - Gun Style IR Thermometer User Manual

Fieldpiece, D=l/10 d l, Applications

Advertising

SIG1

MADE IN TAIWAN

-22°F to 1022°F

10:1

Range

Field of view

Battery

Infrared Gun Style
Thermometer

Fieldpiece

Gun Style Infrared
Thermometer
w/Laser Sight
Model: SIG1

OPERATOR’S MANUAL

Description

The SIG1 thermometer is a low cost, standalone

non-contact infrared thermometer. Simply aim the
thermometer at the target and pull the “trigger” to
display the surface temperature. The temperature
measured will be the average of all the tempera-
tures in the field of view. The closer you are to the
target, the smaller the area. The further away, the
larger the area measured.

Applications

The infrared temperature measurement is fast

and easy. It works best for fast readings, relative
readings (one to another or the same one at differ-
ent times), or temperature readings of hard to reach
places. The following are some applications:

• “Shoot” an inside wall for quick and fast indoor

ambient temperature reading.

• Heating and air conditioning where fast and/or

easy measurement is most important.

• Motor bearings: high temperature can indicate

bearings that might need replacement.

• Circuit breakers: a circuit breaker that is not

operating properly can get hot. By scanning a
panel, you will be able to find the hot one.

• Poor power line connections: a bad connection

can get hot.

IR Temperature Measurement

Objects dissipate heat in the form of infrared (IR)

energy. The hotter it is, the more infrared energy. If
there's enough radiation, you can feel it. The SIG1
infrared thermometer collects infrared energy from
a circular viewing area and measures the total
amount of energy collected. The SIG1 converts the
total energy measured to a temperature. The further
you go from the target, the larger the sampling
space.

If you want to get the temperature of something

small, such as a pipe, you must get close enough
for the pipe to take up the whole viewing area circle.
Otherwise the pipe and the background tempera-
tures will be averaged into the reading.

The accuracy of many infrared temperature

measuring systems is adversely affected by ambi-
ent temperature.

You need to be aware that if the target surface is

reflective enough, it may reflect infrared from other
objects. For example, if you take a reading of a
shiny metal surface, the infrared energy of your face
may reflect enough energy off the surface to affect
the reading. For this reason, it’s a good idea to put
non-reflective tape or paint on reflective surfaces
when taking IR temperature readings.

"Emissivity" of the target surface also affects the

temperature reading. For a given temperature, the
higher the emissivity, the higher the reading. The
lower the emissivity, the lower the reading.

Emissivity of a surface indicates how easy it is for

the infrared to get out. Emissivity for a dull, black
surface is high (nearly 100%) so it's easy for the
infrared to get out. Emissivity for a shiny surface
can be much lower. If the emissivity is low, the
measured temperature will be lower than actual.
For relative readings of the same kind of surface,
this isn't a problem. For some applications, it may
be necessary to spray dull, black paint on the target
to insure a more accurate reading.

For best accuracy use contact sensors (thermo-

couples, thermistors, etc.) anytime you take a tem-
perature measurement. Infrared instruments should
only be used when you aren’t able to touch the sur-
face to be measured.

WARNING

Never point the device towards the eyes

permanent eye damage may occur.

Use extreme caution when using the laser.
Keep out of the reach of children.
Be careful around mirror surfaces since

mirrors can reflect the laser. Looking into the
reflected laser is just as damaging as looking
directly at the laser.

°C °F

HOLD

18.8.8

Specifications

Temperature range: -22 to 1022

F (-30 to 550°C)

Resolution: 1

Response time: 0.25 second
Emissivity: Fixed 0.95
Battery: Standard 9V
Battery life: 9 hrs typical, laser and backlight
Operating temperature: 32 to 122°F (0 to 50°C)
Storage temperature: -4 to 140

F (-20 to 60°C)

Accuracy:

±2%rdg (213 to 1022°F) (100 to 550°C), ±4°F (-22

to 212°F) ±2°C (-30 to 100°C)

Field of view: 10:1
Wave length: Red (630~670nm)
Power out: <1mW, class 2 laser product
Display: 1999 count 3.5 digit LCD
Auto-off: Approx. 10 seconds
Weight: 157g (with battery)
Dimensions: 5.83” x 4.13” x 1.65” (15.81cm

x10.5cm x 4.19cm)

Accessories: Protective cover with strap, battery

(installed), and operator’s manual.

Operation

1. Remove protective plastic cover.
2. Point SIG1 towards target to be measured.
3. Pull trigger to light the target with the laser and

measure its surface temperature.

4. As long as the trigger is held down, the SIG1

will constantly update the measurement and the
blue backlight will illuminate the display.

5. Once the trigger is released, the last measure-

ment will be shown and held until the trigger is
pressed again or until the SIG1 turns off.

Field of View

The SIG1 takes it’s measurement from a circle of

a size determined by a simple ratio of 10:1. The
diameter of this circle is 1/10 the distance between
the target and the tip of the SIG1. For example, if
you’re standing 20 feet from your target, the size of
the circle you’re taking the average temperature of
will be 2 feet wide.

Laser Sight

When the trigger is pulled the red laser dot will

shine about 1/4” above the center of the circular
area being measured by the thermometer. Be sure
to remove protective cap before taking measure-
ments.

°F or °C

To switch between °F and °C open the battery

cover and move the switch to the desired scale.

Battery Replacement

When the 'Low Battery' icon indicates the battery

is low, the battery should be replaced. The battery
is located under the cover at the rear of the SIG1.
The battery should be placed upside down (termi-
nals facing down) so that bunching of the wires is
avoided.

Note: When a new battery is installed, the meter

will power on to show it has recognized the new bat-
tery. Auto-off will occur after 10 seconds without
operation.

Cleaning

Since the laser aperture and lens are delicate,

keep protective plastic cover on the SIG1 when not
in use. When the case gets dirty, clean with a damp
cloth and mild detergent. Do not use abrasives or
solvents.

Warranty

The product is warranted to the original purchas-

er against defects in material or workmanship for a
period of one (1) year from the date of purchase.
During the warranty period, Fieldpiece Instruments
will, at its option, replace or repair the defective unit.

This warranty does not apply to defects resulting

from abuse, neglect, accident, unauthorized repair,
alteration, or unreasonable use of the instrument.

Any implied warranty arising out of the sale of

Fieldpiece's products including but not limited to
implied warranties of merchantability, and fitness for
purpose, are limited to the above. Fieldpiece shall
not be liable for incidental or consequential dam-
ages.

Service

Return any defective SIG1 to Fieldpiece for war-

ranty service along with proof of purchase. Contact
Fieldpiece for out of warranty repair charges.

D=L/10