Denon DN-D4500 - Manual (Page 15)

15
ENGLISH
1. Preset mode
q The preset mode is available when MEMO/PRESET button @4 is pushed for more than 1 sec while
DN-D4500 is in CUE, pause or no disc mode.
w Turn the TRACK SELECT knob o to select the preset item.
e After selecting an item, push the TRACK SELECT knob o down to select the preset data.
r To change other Preset items, repeat these steps.
t Push the MEMO/PRESET button
@4, CUE button !0 or PLAY/PAUSE button !1 to exit from the Preset
mode.
2. Preset items and data
The “*” mark next to the data indicates the default value.
(1) Auto CUE : Auto CUE level search on/off. (A.CUE ON* / A.CUE OFF)
(2) BrakeTime : STEP 1 / STEP 2* / STEP 3 / STEP 4
Set the operating time for the BRAKE mode.
(3) Auto Close : Close OFF / Close 10s / Close 30s* / Close1min
Time for automatically closing disc holder.
(4) Jump Time : Jump10sec* / Jump20sec / Jump30sec / Jump1min
Select the jump time of QuickJump.
(5) P. Range (PITCH RANGE) : 4% Range / 10% Range* / 16% Range / 24% Range
Select the playing pitch range when the power is turned on.
(6) EOM Time :
EOM OFF / EOM 10 sec* / EOM 15 sec / EOM 20 sec / EOM 30sec / EOM 60 sec / EOM 90 sec
Track end message start time.
(7) Fader Mode (FADER START MODE) : Play / CUE* / Play Pause
Select 2-line (TRS) type cable (CUE and Play) or 1 line (TS) type cable (Play and Pause).
(8) Power Play (POWER ON PLAY) : P. Play ON / P. Play OFF*
Playback starts when the power is turned on if a disc is loaded.
(9) Pitch : Pitch ON* / Key. AdjON (KEY ADJUST ON) / Pitch OFF
Select the pitch mode when the power is turned on.
(10) Play Mode (SINGLE / CONTINUOUS / SINGLE PLAY LOCK) : Single / Cont. / Play Lock*
Select the play mode when the power is turned on.
• When SINGLE PLAY LOCK is selected, track selection during playback is disabled. This prevents
playback from stopping when the TRACK SELECT knob o is turned accidentally during playback.
This mode is valid even when selected after turning the power on.
(11) Time Mode (ELAPSED / REMAIN) : Elapsed* / Remain
Select the time mode when the power is turned on.
(12) Bpm Disp (BPM DISPLAY) : Disp ON* / Disp OFF
Select the BPM display
(13) Relay Mode : Relay ON / Relay OFF* :
Relay mode on / off.
• If RELAY MODE is selected by PRESET of CD1 or CD2, RELAY MODE will be selected when the
power is turned on.
(14) Relay Time : Relay Osec* / Relay 1sec / Relay 2sec / Relay 3sec
Select the crossover time the currently playing track when the opposite drive start to play with the
Relay Play function.
(15) Memo Clear (MEMO ALL CLEAR) :
NOTE: This PRESET item can be only performed in CD1 (left side) of the remote controller.
Clear all MEMO data in the non-volatile memory.
q To clear all MEMO data, push the TRACK SELECT knob o down.
• “Clear OK?” flashes on the character display.
w Push the TRACK SELECT knob o down again and select “OK” to execute clearing all MEMO
data.
• “Memo Clear” is displayed on the character display while clearing.
e Once clearing is completed, “Complete!” is displayed.
(16) Version No. The DN-D4500’s software version is displayed. (SYSTEM / DSP)
(17) Preset Int.(PRESET INITIALIZE) : Set all the preset data back to the factory defaults.
q To clear the PRESET data, push the TRACK SELECT knob o down.
“Initial OK?” flashes on the character display.
w Push the TRACK SELECT knob o down again and select “OK” to start clear the preset data.
“Preset Int” is displayed on the character display while data clearing.
e Once clearing is completed, “Complete!” is displayed.
11 PRESET
(2) MEMO CALL [Memo Call]
• When a CD is first loaded that has Memo’s previously saved, the MEMO indicator flashes for 5
seconds.
• To call out the Memo data, select the track that you made MEMO to. *The MEMO indicator lights up.
• Push the MEMO button
@4 to enable Memo call function.
• When the TRACK SELECT knob o is pushed down in the Memo call mode, all the data stored in the
memory is loaded. The DN-D4500 goes to standby mode at the called CUE point.
• When the playing pitch is loaded from the Memo with PITCH LED flashes, playing Pitch is locked until
the Pitch Slider reaches the same saved Pitch value. While playing Pitch is locked & PITCH LED keeps
flashing.
• If you do not wish to save the pitch&key information to memory, please turn the pitch made OFF
before saving your new MEMO.
(3) 1 MEMO CLEAR [Memo Clr]
• To clear one Memo data, select the track that you made MEMO to. Then the MEMO indicator lights
up.
• Push the MEMO button @4 to enable Memo clear mode. Then turn the TRACK SELECT knob o once
clockwise to”Memo Clr?”
• When the TRACK SELECT knob o is pushed down in MEMO CLEAR mode, the Memo data is cleared
and the MEMO indicator on the display turns off.
ALL MEMO CLEAR
• All memory data can be cleared.
• For instructions, see
⁄1 PRESET ”(15) MEMO ALL CLEAR”.
• Be careful as this will delete ALL saved memory.