Studio Technologies 76DA V.4.00 - Manual (Page 47)

Model 76DA/77 User Guide Issue 3, July 2012
Studio Technologies, Inc. Page 47
for Surround
Specifications
Model 76DA Central Controller
General Audio:
Supported Sample Rates: 32, 44.1, 48, 88.2, 96,
176.4, and 192 kHz
Word Length: 24 bits maximum
Internal Processing: 32 bits
Input-to-Output Latency: two samples (e.g., 0.042
milliseconds @ 48 kHz sample rate)
Digital Audio Inputs: five (18 audio channels)
Configuration: two surround (5.1) and three stereo
Type: AES3id-2001/SMPTE 276M (unbalanced
75 ohms/1 Vpp)
Connectors: BNC (per IEC 60169-8 Amendment 2)
Sample Rate Conversion (SRC):
Application: available on Stereo Input C
Input Sample Rate Range: 8 to 216 kHz, limited to
1/6 to 6 times the output sample rate
Latency: 1 millisecond, nominal
Sync Source: configured to follow L/R of currently
selected input or signal connected to sync input
Sync Input:
Compatible Sources: word clock, DRS (AES11),
bi-level video, tri-level video
Jitter: 4 ns pp maximum
Connector: BNC (per IEC 60169-8 Amendment 2)
Termination: 75 ohms, selectable on/off
Digital Monitor Outputs: 16 (eight pairs)
Configuration: organized as two surround (5.1)
and two stereo
Dynamic Range: 135 dB
Type: AES3 (110 ohms/5 Vpp) or AES3id/SMPTE
276M (75 ohms/1 Vpp), selectable
Connector: 25-pin D-subminiature female (DB-25F)
Analog Monitor Outputs: 8
Configuration: organized as one surround (5.1)
and one stereo (2-channel)
Type: electronically balanced, source impedance
200 ohms
Nominal Level: +4.0 dBu @ –20 dBFS input
source and level control at maximum setting
Maximum Level: +24 dBu into 2000 (2 k) ohms
or greater
Frequency Response, Digital Inputs to Analog
Monitor Outputs: 10 Hz-20 kHz +0.0/–0.3 dB @
48 kHz sample rate; –3 dB @ 64 kHz
Distortion (THD+N): 0.004%, ref 1 kHz, +4 dBu
output
S/N Ratio: 89 dB, ref +4 dBu output
Dynamic Range: greater than 109 dB
Crosstalk: –98 dB at 1 kHz; –97 dB at 16 kHz,
ref –1 dBFS input
Connector: 25-pin D-subminiature female (DB-25F)
Configurable Delay: 0 to 340 milliseconds @
48 kHz sample rate (scales up or down depending
on actual sample rate)
Post-Fader Monitor Output Level Offsets:
each surround and stereo channel independently
adjustable in 0.5-dB steps over a ±12-dB range.
(Digital and analog outputs associated with a
specific channel share the same setting.)
Bass Management:
Crossover Frequency and Type: –6 dB @
80 Hz, symmetrical for low-pass and high-pass
filters, maximally flat
Filter Slope: 12 or 24 dB/octave
Overall Operation: independent on/off selectable
for surround and stereo post-fader monitor outputs
Downmix:
Functions: surround to stereo, stereo to mono
Surround to Stereo:
L @ 0 or –3 dB;
R @ 0 or –3 dB;
C @ –3 or –6 dB summed with L and R;
LFE @ full attenuation or –6 dB summed with
L and R;
LS @ –3 or –6 dB summed with L;
RS @ –3 or –6 summed with R;
C, SUB, LS, and RS monitor outputs mute
Stereo to Mono:
L @ –3 dB summed with R @ –3 dB to C;
L, R, LS, RS, and SUB monitor outputs mute
For a surround input this results in the C output be-
ing the sum of L @ –3 or –6 dB, R @ –3 or –6 dB;
C @ –3 or –6 dB, LFE @ full attenuation or –6 dB;
LS @ –6 or –9 dB, and RS @ –6 or –9 dB.