Kichler 15191 - Manual

WARNING – RISK OF ELECTRIC SHOCK
• Use only in ponds and small decorative fountains where persons will
immerse no more than their hands and lower arms while the product
is energized.
• DO NOT use in water intended for swimming, wading, immersion, or
bathing.
• All installer completed cable connections must be located outside of
pond or fountain.
• Low voltage circuit must be supplied by a power unit marked as
suitable for supplying submersible luminaires.
• Power unit must be supplied by a branch circuit protected by a ground
fault circuit interrupter (GFCI).
• Maximum Depth: 72” (1.8m)
• Do not mount luminaire within 10 feet (3m) of a swimming pool, spa or
fountain.
• This fixture is to be used only with a Kichler low voltage lighting power
unit (transformer) rated a maximum 15 volts, 300 W per secondary (25
AMPS).
• According to the requirements of the National Electric Code (NEC),
direct burial rated wire is to be buried a minimum of 6” [152mm]
beneath the surface of the ground.
NOTE: If additional Direct Burial wire is needed, contact your local
Kichler ® landscape distributor.
• 8 GA wire can be purchased in length of 250’ (76 M), 15503-BK.
• 10 GA wire can be purchased in length of 250’ (76 M), 15504-BK.
• 12 GA wire can be purchased in lengths of 100’ (30 M), 15501-BK;
250’ (76 M), 15502-BK; 500’ (152M), 15505-BK; and 1000’ (304 M),
15506-BK.
• Fixture shall not use a tungsten halogen lamp unless the fixture is
markedfor use with such lamps.
• Wiring connections must be made with approved/listed wire connection
device(s) suitable for the application. Do not exceed manufacturers’
wiring combination specifications for size and quantity of conductors.
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
This fixture is intended for installation in accordance with the National
Electric Code (NEC) and Local code specifications. Failure to adhere to
these codes and instructions may result in serious injury and/or property
damage and will void the warranty.
OUTDOOR USE ONLY
INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO
PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1) Turn off / unplug and allow to cool before replacing lamp.
2) Lamp gets HOT quickly! Contact only switch / plug when turning on.
3) Do not touch hot lens or cowl.
4) Do not remain in light if skin feels warm. (Light is intense, it may cause
“sunburn”.)
5) Do not look directly at lighted lamp.
6) Keep lamp away from materials that may burn.
7) Use only with wattage and lamp marked on fixture.
8) Do not touch the inner glass envelope of the lamp at any time. Use a soft
cloth. Oil from skin may damage lamp.
9) Do not operate the fixture with a damaged or missing lens.
ASSEMBLY AND INSTALLATION
1) Turn off power.
2) Twist cover counter clock-wise and remove.
3) Remove lens.
4) Insert recommended lamp into socket.
NOTE: Use caution when installing. Hold lamp by outer housing.
DO NOT touch glass envelope inside. If this happens, clean lamp with
denatured alcohol and a lint free cloth.
5) Reassemble lens and cover to housing. Turn cover until it snaps into place.
NOTE: If O-Ring comes out during assembly, lay O-Ring on ledge
inside of housing before assembling. Do not assemble without O-Ring
in place.
6) Make wire connections directly to a low voltage transformer or connect to
low voltage power supply cable using the appropriate connectors.
Connection from the fixture cable to power supply cable should not be
submerged. (Connectors sold separately,
7) Support base and adjust housing to desired direction.
8) Submerge fixture.
Date Issued: 7/15/11 IS-15191-US
COVER
TAPA
O-RING
ANILLO EN O
LENS
LENTE
HOUSING
CUBIERTA
LEDGE
REBORDE
LAMP
LAMPARA
BASE
BASE
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page