Kichler 43191 - Manual

1) Pass wire from fixture through stems and screw stems into
couplings on top of fixture body.
NOTE: Thread locking compound must be applied to all stem
threads as noted with symbol (3) to prevent accidental
rotation of fixture during cleaning, relamping, etc.
2) Pass fixture wire through remaining stems and screw stems
together.
3) The canopy has one set of loop/chain link/loop pre-installed.
Starting with that loop/chain link/loop, pass fixture wire
through the threaded pipe on the first small loop. Next pass
the fixture wire through the hole in the small loop attached to
canopy and through the hole in the canopy.
4) With the set of loop/chain link/loop not pre-installed, from the
second set of stems, pass the fixture wire through the hole in
the threaded pipe on the end of one small loop. Thread that
small loop to the end of the last stem.
5) Pass fixture wire through hole in second small loop. Pass
fixture wire through hole in canopy. Pass threaded pipe at end
of second loop through hole in canopy. Thread wing nut onto
end of threaded pipe. Tighten wing nut to secure loop to canopy.
6) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room that
you are working on.
c) Place the wall switch in the “OFF” position. If the fixture to
be replaced has a switch or pull chain, place those in the
“OFF” position.
7) Thread hexnut onto threaded pipe so that 5 threads are
exposed above hexnut. Thread that end of threaded pipe
into mounting strap and tighten hexnut against mounting strap.
8) Run another hexnut down threaded pipe almost touching
first hexnut. Now screw threaded pipe into mounting strap.
Mounting strap must be positioned with extruded thread
faced into outlet box. Threaded pipe must protrude out the
back of mounting strap. Screw third hexnut onto end of
threaded pipe protruding from back of mounting strap.
9) Attach mounting strap to outlet box. (Screws not provided.)
10) Attach safety cable to slot in mounting strap.
11) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole
and two raise dimples. Wrap ground wire from outlet box
around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Put
ground wire from outlet box under cupped washer and
green ground screw and thread screw into hole in mounting
strap.
If fixture is provided with ground wire. Connect fixture ground
wire to outlet box ground wire with wire connector, (not
provided) after following the above steps. Never connect
ground wire to black or white power supply wires.
12) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
GREEN GROUND
SCREW
CUPPED
WASHER
A B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
IS-43191-US Date Issued: 7/25/14
3
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
4
MOUNTING STRAP
PLANCHA PARA MONTAR
CANOPY
ESCUDETE
STEM
VARILLA
HEXNUT
TUERCA HEXAGONAL
FINIAL
REMATE
SAFETY CABLE
CABLE DE SEGURIDAD
GLASS
VIDRIO
WING NUT
TUERCA DE MARIPOSA
3
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
13) Push fixture to ceiling, carefully passing threaded pipe through
hole in canopy.
14) Thread hexnut onto end of threaded pipe protruding from
canopy. Tighten hexnut up against canopy.
15) Thread finial onto end of threaded pipe. (DO NOT over tighten.)
16) Set glass down over sockets.
SMALL LOOP
ARGOLLA PEQUEÑA
CHAIN LINK
ESLABÓN DE
CADENA