Epson DW746 - Manual (Page 12)

If the fence head glide strips (arrows below) become worn
or damaged, it can easily be replaced. Consult your local
D
E WALT Service Center for parts and assistance.
Accessories
Recommended accessories for use with your tool are
available at extra cost from your distributor or local service
center.
D
E WALT manufactures the following accessories for your
saw:
DW7460 - Mobile base
DW7461 - Sliding Table and Premium Gauge
DW7462 - Iron Wing
DW7463 - Outfeed Table
DW7464 - 52” Rail System with Legs and Table Board
DW7466 - Dado Throat Plate
DW7467 - Steel Wing
DW7468 - 30” Rail System with Legs and Table Board
DW7469 - Low Profile Fence Face
DW7471 - Enhanced Miter Gauge
CAUTION: The use of any non-recommended
accessory may be hazardous.
If you need assistance in locating any accessory, please
contact D
E WALT Industrial Tool Co., 701 East Joppa
Road, Baltimore, MD 21286 or call
1-800-4-D
E WALT (1-800-433-9258).
Important
To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed by
authorized service centers or other qualified service
organizations, always using identical replacement parts.
Full Warranty
This saw warranted for two years from date of purchase.
We will repair, without charge, any defects due to faulty
materials or workmanship. For warranty repair information,
call 1-800-4-D
E WALT. This warranty does not apply to
accessories or damage caused where repairs have been
made or attempted by others. This warranty gives you
specific legal rights and you may have other rights which
vary in certain states or provinces.
In addition to the warranty, D
E WALT tools are covered by
our:
30 DAY NO RISK SATISFACTION GUARANTEE
If you are not completely satisfied with the performance of
9
English
Over time, the lubricants used in the mechanism of
your tablesaw may need to be replenished.
HEIGHT AND BEVEL GEAR (FIG. 22):
First clean off any accumulated sawdust from the gears
and the worms with a stiff brush. Next, remove any pitch or
resin which has built up. You may need to use a solvent
such as mineral spirits to remove it. Next, re-apply grease
to the worms (A) to the gears (B) and the washer/pin
assembly(C). You can also apply paste wax to the gears if
you find that the grease is attracting too much sawdust. If
any backlash has occurred in the bevel system, you can re-
adjust the bevel gear clearance by loosening the two
screws (D) which hold the gear to the cradle, letting the
gear fall into tighter mesh, lightly tightening the screws,
rotating the worm one full turn to set the gear height, then
fully tightening the gear retaining screws. This adjustment
must be made at 0˚ bevel.
BEVEL PIVOT:
The bevel pivot trunnions, both front and back should also
be maintained. First clean them like the gears were
cleaned. Then apply grease into the curved slots (E) and
bevel the saw back and forth to distribute the grease.
ARBOR PIVOT:
You may also need to lubricate the arbor pivot pin (F). This
can be done by applying a light oil at both the base and
top of the pivot pin.
Lubricating Fence Head
The moving parts of your fence head should be periodically
greased. This includes the area between the cams and
locking levers (A), and between the cams and the fence
head casting (B).
Maintaining Fence System
Your fence should always slide freely. If it seems to require
excessive force to slide or if it feels rough, wipe the rails
and fence head gliding surface with a cloth or paper towel.
Check the movement again. If it still feels rough, clean the
fence head with a mild solvent such as denatured alcohol
or mineral spirits. Re-coat the rail with a heavy coat of
paste wax or a light oil. Slide the fence head back and
forth several times to coat the rail and fence. Wipe off any
excess wax or oil from the rail.
your D E WALT heavy duty industrial tool, simply return it to the
participating seller within 30 days for a full refund. Please
return the complete unit, transportation prepaid. Proof of
purchase may be required.