PLANET FGSW-2620 - Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 24-port 10/100Mbps +
2-port Unmanaged Gigabit Ethernet Switch, FGSW-2620.
The term “Fast Ethernet Switch” mentioned in this user’s
manual refers to the FGSW-2620.
The box should contain the following items:
 24-port 10/100Mbps+ 2-port Gigabit Ethernet Switch x 1
 User’s Manual x 1
 Power Cord x 1
 Rubber Feet x 4
 Two rack-mounting brackets with attachment screws x 6
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.
3. Product Specifications
Model FGSW-2620
Hardware Specifications
Hardware Version V5
10/100BASE-Tx MDI/MDIX Ports 24
10/100/1000BASE-T MDI/MDIX
Ports
2
Throughput (packet per second) 6.54Mpps
Switch Fabric 8.8Gbps
Weight 1.7kg
Power Consumption / Dissipation 6.8 watts / 23BTU
Power Requirements 100~240V AC, 50/60Hz, 0.2A
Dimensions (W x D x H) 440 x 180 x 44mm, 1U height
Switch Processing Scheme Store-and-Forward
Address Table 8K entries
SRAM Packet Buffer 4.1Mbit
Jumbo Packet Size 9K
Power Green Ethernet From 10m to 100m saving up to 12%
5. Switch Rear Panel
Figure 2 shows the rear panel of Fast Ethernet Switch.
Figure 2: FGSW-2620 Rear Panel
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is powered. If
your networks should be active all the time,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will
prevent you from network data loss or
network downtime.
2. In some area, installing a surge suppression
device may also help to protect your Fast
Ethernet Switch from being damaged by
unregulated surge or current to the Switch
or the power adapter.
4. Switch Front Panel
Figure 1 shows the front panel of Fast Ethernet Switch.
Figure 1: FGSW-2620 Front Panel
LED Indicators
System
LED Color Function
PWR Green It indicates the Switch is turned on when lit.
Per 10/100Mbps port
LED Color Function
LNK/ACT Green
It indicates the link through that port is
established successfully at 10/100Mbps
when lit.
It indicates the Switch is actively
sending or receiving data over that port
when it is blinking.
2. Product Features
Physical Port

24 10/100Mbps Fast Ethernet ports
 2 10/100/1000Mbps Gigabit Ethernet ports
 Supports auto MDI/MDI-X function
Layer 2 Features

Complies with IEEE 802.3, 10Base-T, IEEE 802.3u
100BASE-TX, IEEE 802.3ab Gigabit Ethernet standard
 Supports powerful Green Ethernet for power saving
 Features Store-and-Forward mode with wire-speed
filtering and forwarding rates
 9K Jumbo Frame size
 Complies with IEEE 802.3x flow control for full duplex
operation and back pressure for half duplex operation
 Integrated address look-up engine, supporting 8K abso-
lute MAC addresses
 Automatic address learning and address aging
 Supports CSMA/CD protocol
Hardware Features

100~240V AC, 50/60Hz, 0.2A universal power input
 FCC, CE Class A compliant
Flow Control
Back pressure for half duplex, IEEE
802.3x Pause frame for full duplex
Temperature
Operating: 0~50 degrees C
Storage: -10~70 degrees C
Operating Humidity
5% to 90%, Storage: 5% to 90%
(non-condensing)
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab(Gigabit Ethernet)
IEEE 802.3x (Full-duplex Flow Control)
IEEE 802.1p (Quality of Service)
Per 10/100/1000Mbps port
LED Color Function
LNK/ACT Green
It indicates the port is running at
10/100/1000Mbps when lit.
1000Mbps Green
It indicates the port is running at
1000Mbps when lit.
It indicates the port is operating at
10/100Mbps when turned off.
6. Installing the Switch
This part describes how to install your Fast Ethernet Switch
and make connections to it. Please read the following topics
and perform the procedures in the order being presented.
Note
This Fast Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Fast Ethernet Switch on the desk, simply
follow the steps below:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Fast Ethernet Switch.
Step 2: Place the Fast Ethernet Switch on the desk near
an AC power source
Step 3: Keep enough ventilation space between the Fast
Ethernet Switch and the surrounding objects.