PLANET FNSW-1601 - Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Content
Thank you for purchasing PLANET 16/24-Port 10/100Mbps
unmanaged Fast Ethernet Switch, FNSW-1601 / FNSW-
2401. Terms of “Switch” in following section of this User’s
Manual means the FNSW-1601 / FNSW-2401.
Upon open the box of the Switch and carefully unpack it.
The box should contain the following items:
l The Fast Ethernet Switch x 1
l User’s Manual x 1
l Power Cord x 1
l Rubber Feet x 4
l Two rack-mounting brackets with attachment screws x 8
If any of these are missing or damaged, please contact your
dealer immediately, if possible, retain the carton including
the original packing material, and use them against to
repack the product in case there is a need to return it to us
for repair.
3. Product Specification
Product FNSW-1601 FNSW-2401
Hardware Specification
10/100Base-T MDI/MDIX Ports 16
24
Throughput (packet per second) 2.38Mpps 3.57Mpps
Switch fabric 3.2Gbps 4.8Gbps
Weight 2.08kg 2.21kg
Power Consumption /
Dissipation
7.3 watts / 25 BTU 10 watts / 34 BTU
Power Requirement 100~240 VAC, 0.6A, 50-60 Hz
Dimensions (W x D x H) 440 x 180 x 44mm, 1U height
Switch Processing Scheme Store-and-Forward
Address Table 8K entries
Power Green Ethernet
10m ~ 50m:
Saving up to 22%
10m ~ 50m:
Saving up to 12%
Flow Control
Back pressure for half duplex, IEEE
802.3x Pause Frame for full duplex
Temperature
Operating: 0~50 Degree C
Storage: -10~70 Degree C
Humidity Operating:
5% to 90%, Storage: 5% to 90% (Non-
condensing)
Standards Conformance
Regulation Compliance
FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3x (Full-duplex Flow Control)
IEEE 802.1p (Quality of Service)
6. Installing the Switch
This part describes how to install your Fast Ethernet Switch
and make connections to it. Please read the following topics
and perform the procedures in the order being presented.
Note
This Fast Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Fast Ethernet Switch on desktop, simply follow
the next steps:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Fast Ethernet Switch.
Step 2: Place the Fast Ethernet Switch on desktop near an
AC power source.
Step 3: Keep enough ventilation space between the Fast
Ethernet Switch and the surrounding objects.
Per 10/100Mbps port
LED Color Function
LNK /
ACT
Green
Lights to indicate the link through that
port is established successfully.
Blinks indicate that the Switch is
actively sending or receiving data over
that port.
100Mbps Green
Lights to indicate the port is run at
100Mbps.
Off: indicate that the port is operating
at 10Mbps.
2. Product Features
l Comply with IEEE 802.3, 10Base-T, IEEE 802.3u 100Base-
TX Ethernet standard
l 16/24-Port 10/100Mbps Fast Ethernet ports
l Supports powerful Green Ethernet to power saving
l Features Store-and-Forward mode with wire-speed
filtering and forwarding rates
l Hardware based 10/100Mbps, half / full duplex mode,
flow control, auto-negotiation
l Comply IEEE 802.3x flow control for full duplex operation
and Backpressure for half duplex operation
l Comply IEEE 802.1p Quality of Service
l Integrated address look-up engine, support 8K absolute
MAC addresses
l Automatic address learning and address aging
l Supports Auto MDI/MDI-X function
l Support CSMA/CD protocol
l 100~240V AC, 0.6A, 50~60Hz universal Power input
l FCC, CE class A compliant
4. Switch Front Panel
Figure 1 & 2 shows a front panel of Fast Ethernet Switch.
Figure 1: FNSW-1601 front panel
Figure 2: FNSW-2401 front panel
LED Indicators
FNSW-1601 / FNSW-2401
System
LED Color Function
PWR Green
Lights to indicate that the Switch has
power.
5. Switch Rear Panel
Figure 3 shows a front panel of Fast Ethernet Switch.
Figure 3: FNSW-1601 / FNSW-2401 rear panel
Power
Notice
1. The device is a power-required device, it
means, it will not work till it is powered. If
your networks should active all the time,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will
prevent you from network data loss or
network downtime.
2. In some area, installing a surge suppression
device may also help to protect your Fast
Ethernet Switch from being damaged by
unregulated surge or current to the Switch
or the power adapter.
Step 4: Connect your Fast Ethernet Switch to network
devices.
A. Connect one end of a standard network cable to
the 10/100 RJ-45 ports on the front of the Fast
Ethernet Switch.
B. Connect the other end of the cable to the network
devices such as printer servers, workstations or
routers…etc.
Step 5: Supply power to the Fast Ethernet Switch.
A. Connect one end of the power cable to the Fast
Ethernet Switch.
B. Connect the power plug of the power cable to a
standard wall outlet.
When the Fast Ethernet Switch receives power, the Power
LED should remain solid Green.