Edelbrock 2103 User Manual
Edelbrock For the car
PERFORMER-PLUS
CAMSHAFT / LIFTERS / LUBE KIT
CATALOG # 2103
MODEL: 400 c.i.d. Chevrolet V8 engines
GENERAL INSTRUCTIONS
• Please study these instructions carefully before you remove your stock camshaft. If you have any questions or problems, do not hesitate to contact
our Technical Hotline at: 1-800-416-8628.
• These instructions are designed to give general installation guidelines. A complete step-by-step procedure manual would require many pages. If you
are a novice or just learning to work on automotive engines, we recommend consulting either Chilton or Motors automotive manuals before you
begin. You may also wish to contact an experienced mechanic. Be advised: improper installation may result in LOW MILEAGE, POOR PERFORMANCE,
COSTLY REINSTALLATION AND EVEN ENGINE DAMAGE. Installing a camshaft is a complex procedure. Please follow these instructions carefully.
Failure to do so may void your warranty.
• Before you begin the removal and installation process, please examine the kit for possible shipping damage. If the camshaft is damaged, contact
your dealer immediately. Also, make sure you have all the recommended tools and parts as listed below. As you read through these instructions the
first time, use the preparation checklist to check off the exact items you will need.
•
Performer-Plus camshafts are ground specifically for use with the corresponding Performer manifold #2101 or #3701. Both are dyno-matched and
street proven to work as a team; especially when matched with Edelbrock Tubular Exhaust Systems. However, the Performer camshaft may be used
by itself. Edelbrock Performer-Plus cam #2103 is street legal in all 50 states - E.O.#D-215-19.
1. Disconnect the battery.
2. Drain radiator coolant. Drain plug will normally be located on lower
right or left side of the radiator facing the engine.
3. Remove radiator and air conditioning condenser if so equipped. In
some cases, the front grille may have to be removed. Measure dis-
tance from front cover to grille or brackets that may interfere with
camshaft against the length of the camshaft.
4. Remove the gas cap to relieve pressure. Disconnect fuel line and plug.
Replace gas cap.
5. Disconnect all linkage from carburetor such as throttle, throttle
springs, transmission, cruise control and automatic choke.
6. Tag and remove coil wires and sensor wires.
7. Tag and remove vacuum lines.
8. Remove valve covers.
9. Remove distributor cap and wires, rotate engine until rotor points
towards number 1 terminal in cap and pointer on front cover is on top
dead center (TDC) and remove distributor. Note the approximate posi-
tion of the distributor housing in relation to the manifold to assist in
getting the distributor properly located during re-installation.
10. Remove carburetor and intake manifold. Remove and discard intake
manifold gasket.
11. Remove rocker arms and pushrods.
12. Remove hydraulic valve lifters.
13. Remove crankshaft pulley, and using a suitable puller, crankshaft
dampener.
14. Loosen oil pan and remove water pump and front cover.
NOTE: The front cover oil seal should be replaced before the front cover is
re-installed.
PREPARATION CHECKLIST
Hardware & Parts To Buy
•
Gaskets - Edelbrock,
OEM or equivalent
•
Pipe plugs, if needed
•
Edelbrock Gasgacinch #9300
•
RTV Silicone Sealant
•
Chalk
•
Paper and pencil
•
Radiator coolant
•
Edelbrock Sure Seat Valve Springs,
#5802 or #5902 (for rotators)
•
Edelbrock Performer-Link True Rolling
Timing Chain and Gear Set, #7800
•
Teflon tape
•
Front cover oil seal,
OEM or equivalent
Tools & Equipment For Installation
•
Box and open end wrenches
•
Socket set
•
Distributor wrench
•
Pliers (channel locks & hose clamp)
•
Screw drivers (regular and phillips)
•
Torque wrench
•
Hammer
•
Gasket scraper or putty knife
•
Timing light Vacuum gauge
•
Rags
•
Water bucket
•
Harmonic balancer puller
•
Masking tape (for tagging hoses and electrical wires)
•
Engine oil & filter
•
Crankshaft dampener puller
NOTE: Sure seat springs #5902 not applicable to cylinder heads 1977 and later with casting #14014416. These heads must use Edelbrock spring set
#5802.
REMOVAL OF ENGINE PARTS BEFORE CAMSHAFT INSTALLATION
Be sure to keep all parts in order
WARNING! DO NOT REMOVE RADIATOR CAP OR
RADIATOR HOSES WHILE ENGINE IS HOT!
©2008 Edelbrock Corp.
Rev. 9/08 - AJ/mc
Brochure #63-2103