Canon CR-N700 4K PTZ Camera with 15x (Satin Black) - Manual (Page 2)

When installing the camera at a high place , use the ceiling plate to fix the
camera . Fix the ceiling plate tightly with four M4 screws ( pan head , binding
head , etc .).
When working with the camera upside down , support the camera to prevent
it from wobbling in order to attach or remove the rubber feet or the camera -
to - mount safety wire . Keep the four rubber feet and four screws that have
been removed for reuse in case of a change in the installation .
Ceiling mount
The camera is hung upside down from the ceiling or other location using the
ceiling plate .
The procedure provided in the "Installation Guide / Important Information" [2 / 2]
explains this installation method . The weight of the camera ( body only ) is
Approx . 4 . 4 kg ( 9 . 7 lb .). Reinforce the ceiling depending on its structure and
material to ensure the sufficient holding strength to support the total weight
including the camera and the mounting parts , and install .
Standing mount
The camera is fixed to a high place using the ceiling plate .
Follow the same procedure as for the ceiling mount , except for the direction
of the camera and logo plate inversion .
Tripod mount
Attach the tripod by fixing two screws to the two screw holes for tripod .
Use 1 / 4 - 20UNC screws and tighten them securely , and set the tripod on a
flat surface with no steps .
Also refer to the instructions in the "Installation Guide / Important Information"
[2 / 2] , if necessary .
4.5 – 5.5 mm (0.18 – 0.22 in.)
1/4-20UNC
Desktop
Install the camera on a stable , horizontal surface such as a table .
Also refer to the instructions in the "Installation Guide / Important Information"
[2 / 2] , if necessary .
Connecting the Camera
1 3 4 2 5 7 6 8 9 10
11 12 13 14 16 15
1. LAN terminal
This terminal is for a network connection ( RJ - 45 connector ).
The built - in PoE ++ ( Power over Ethernet ++) function allows the camera to be
powered by a PoE ++ HUB that complies with IEEE802 . 3bt Type 3 or higher
via a LAN cable .
Use a category 5e or higher STP ( shielded type ) LAN cable , up to 100 m ( 328 ft .)
in length .
Important
• Some PoE ++ HUBs can limit the power for each port , but applying limits
may interfere with performance . In this case , do not limit the power .
• Some PoE ++ HUBs have limits for the total power consumption for
the ports , which can interfere with performance when multiple ports
are in use . For more information , check the instruction guide for the
corresponding PoE ++ HUB .
2. SD card slot
For future expansion .
3. RESET switch
Initialize the camera settings to the factory defaults . Refer to the "Settings
Guide" for details .
4. 12G-SDI OUT terminal
Terminal for 12G - SDI output ( BNC ).
5. SERVICE switch
Set the camera number and frame frequency operated by the IR remote
controller .
( Refer to "Before using the camera" > "SERVICE switch settings" .)
6. TIME CODE terminal
Terminal for time code input / output ( BNC ).
7. Memory card slot
For future expansion .
8. 3G-SDI OUT terminal
Terminal for 3G - SDI output ( BNC ).
9. GEN-LOCK/SYNC terminal
Terminal for the synchronization signal input / output ( BNC ) to synchronize the
videos from the camera and external devices .
If the reference signal is unstable , external synchronization is not possible .
Subcarriers do not synchronize .
10. INPUT1/INPUT2 terminal
XLR terminals for audio input . It can be used for microphone / line input .
• Microphone power ( Phantom power ) : 48 V DC
11. LED for phantom power supply
It is lit in blue when the phantom power is supplied .
12. MIC terminal
Stereo 3 . 5 mm ( 0 . 14 in .) terminal for audio input . It can be used for
microphone / line input .
• Microphone power: 2 . 4 V DC
13. RS-422 terminal
Serial terminal ( RJ - 45 connector ) for RS - 422 .
Connect the GNDs on both ends to stabilize the voltage level of the signal .
Use category 5e or higher STP cables .
Pin number Function
1 TX - Output (-)
2 TX + Output (+)
3 RX - Input (-)
4 GND –
5 GND –
6 RX + Input (+)
7 NC –
8 NC –
14. HDMI OUT terminal
Terminal for HDMI output .
15. DC IN 12V terminal
Pow er supply terminal for the external DC power supply .
Connect to the power supply that meets the installation site requirements
( approved products and the environment ) and product specifications .
In addition , note that inrush current may cause the power supply to be
insufficient and cause failure when power is turned on . Therefore , it is
recommended to use a power supply with a power capacity of two to three
times the rated capacity or more .
• Input: 10 . 8 V – 20 V DC , 3 . 5 A ( acceptable maximum load current ).
4 - pin XLR connector .
Pin number Function
4 3 2 1
1 GND
2 NC
3 NC
4 10 . 8 – 20 V DC
16. GND terminal
Ground terminal of the camera .
It is used to install a lightning arrester ( surge protection devices ).
Note
• The camera is not equipped with a power switch . To turn the camera on
and off , insert and remove the cable of the external DC power supply
connected to the "15 . DC IN 12V terminal" or the PoE ++ HUB connected
to the "1 . LAN terminal" , which supplies power .
When both the PoE ++ HUB and the external DC power supply are
connected , the external DC power supply takes priority . If the external
DC power supply is disconnected while both are connected , power to
the camera will be interrupted . In this case , power can be restored by
disconnecting and reconnecting the LAN cable .
• The audio input terminals ( "10 . INPUT1 / INPUT2 terminal" , "12 . MIC
terminal" ) and microphones should be set using the Settings Page . Refer
to the "Settings Guide" for details .
Specifications
Please refer to the ' Specifications ' in the ' Appendix ' of the "Settings Guide"
for specifications not listed below .
Pan operation range: Horizontal ± 170 °
Tilt operation range: Vertical - 30 ° – + 90 °
Operating Environment: Temperature: 0 – + 40 (+ 32 ° F – + 104 ° F )
Humidity: 10% – 90% ( without condensation )
Storage Environment: Temperature: 0 – + 40 (+ 32 ° F – + 104 ° F )
Humidity: 10% – 90% ( without condensation )
Power Consumption: PoE ++ Input: Approx . 37 . 4 W * max . ( body only )
DC Input: Approx . 36 . 7 W max . ( body only )
* Class 5 ( 40 . 0 W required ) for power supply devices
Dimensions ( W x H x D ) : Approx . 200 x 269 x 208 mm ( 7 . 87 x 10 . 59 x 8 . 19 in .)
( excluding protrusions )
Weight: Approx . 4 . 4 kg ( 9 . 7 lb .) ( body only )
Country Regulations
About wireless communication
Regarding countries and regions where radio communication functions are
acceptable
Since the utilization of the radio communication functions can be legally
restricted by a country or region , it may not be possible to utilize out of the
country or the region where the product is purchased . Canon shall not be
liable for any incidents that may incur as a result of the utilization of the
radio communication functions in any country or region other than where the
product is purchased .
FCC NOTICE
Remote Camera , Model Name: CR - N700
This device complies with Part 15 of the FCC Rules . Operation is subject
to the following two conditions: ( 1 ) This device may not cause harmful
interference , and ( 2 ) this device must accept any interference received ,
including interference that may cause undesired operation .
Note: This equipment has been tested and found to comply with the limits for
a Class A digital device , pursuant to Part 15 of the FCC Rules .
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment .
This equipment generates , uses , and can radiate radio frequency energy
and , if not installed and used in accordance with the user manual , may cause
harmful interference to radio communications . Operation of this equipment
in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense .
Do not make any changes or modifications to the equipment unless
otherwise specified in the manual . If such changes or modifications should
be made , you could be required to stop operation of the equipment .
Use of shielded cable is required to comply with class A limits in Subpart B
of Part 15 of FCC Rules .
Model: CR - N700 ( including WLAN Module Model ES202 , FCC ID: AZD239 /
IC: 498J - 239 )
This device complies with Part 15 of FCC Rules and ISED ' s applicable
licenceexempt RSS standard ( s ). Operation is subject to the following two
conditions:
( 1 ) this device may not cause interference , and
( 2 ) this device must accept anyinterference , including interference that may
cause undesired operation of this device .
This equipment complies with FCC / ISED radiation exposure limits set
forth for an uncontrolled environment and meets the FCC radio frequency
( RF ) Exposure Guidelines and RSS - 102 of the ISED radio frequency ( RF )
Exposure rules . This equipment should be installed and operated keeping
the radiator at least 20 cm or more away from person ' s body .
This transmitter must not be co - located or operated in conjunction with any
other antenna or transmitter .
FDA regulation
This product has not been evaluated by the Food and Drug Administration
( FDA ) for use as a medical device . When incorporated into a system with
medical applications , FDA regulations may apply . Therefore , please consult
your legal advisor to determine whether FDA regulations apply .
Complies with
IMDA Standards
DB00671
European Union regulatory notices:
Remote Camera , Model Name: CR - N700
Warning
This is a class A product . In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures .
Use of shielded network cable is required to comply with Class A limits in
EN55032 .
Wireless LAN Specifications
Frequency range: 2 , 401 MHz – 2 , 473 MHz
Maximum output power: 9 . 48 dBm
For EU
Hereby , Canon Inc ., declares that the radio equipment type CR - N700 is in
compliance with Directive 2014 / 53 / EU . The full text of the EU declaration of
conformity is available at the following internet address:
http: // www . canon - europe . com / ce - documentation
For UK
Hereby , Canon Inc ., declares that the radio equipment type CR - N700 is
in compliance with the relevant statutory requirements . The full text of the
declaration of conformity is available at the following internet address:
https: // www . canon - europe . com / ce - documentation /
Only for European Union and EEA ( Norway , Iceland and Liechtenstein ) and
United Kingdom
These symbols indicate that this product is not to be disposed of with your
household waste , according to the WEEE Directive
( 2012 / 19 / EU ), the Battery Directive ( 2006 / 66 / EC ) and / or
national legislation implementing those Directives and
the UK Waste Electrical and Electronic Equipment
Regulations and the UK Batteries and Accumulators
Regulations .
If a chemical symbol is printed beneath the symbol shown above ,
in accordance with the Battery Directive and the UK Batteries and
Accumulators Regulations , this indicates that a heavy metal ( Hg = Mercury ,
Cd = Cadmium , Pb = Lead ) is present in this battery or accumulator at
a concentration above an applicable threshold specified in the Battery
Directive and the UK Batteries and Accumulators Regulations .
This product should be handed over to a designated collection point , e . g .,
on an authorized one - for - one basis when you buy a new similar product or
to an authorized collection site for recycling waste electrical and electronic
equipment ( EEE ) and batteries and accumulators . Improper handling of
this type of waste could have a possible impact on the environment and
human health due to potentially hazardous substances that are generally
associated with EEE . Your cooperation in the correct disposal of this product
will contribute to the effective usage of natural resources .
For more information about the recycling of this product , please contact your
local city office , waste authority , approved scheme or your household waste
disposal service or visit www . canon - europe . com / sustainability / approach /.
CANON INC .
30 - 2 , Shimomaruko 3 - chome , Ohta - ku , Tokyo 146 - 8501 , Japan
Canon U . S . A . Inc .
One Canon Park , Melville , NY 11747 , U . S . A .
Tel No . 1 - 800 - OK - CANON ( 1 - 800 - 652 - 2666 )
CANON EUROPA N . V .
Bovenkerkerweg 59 , 1185 XB Amstelveen , The Netherlands