Document Outline

• Jackrabbit (BL1800) User's Manual
  • Table of Contents
  • 1. Introduction
    • 1.1 Features
    • 1.2 Development and Evaluation Tools
    • 1.3 How to Use This Manual
      • 1.3.1 Additional Product Information
      • 1.3.2 Online Documentation
    • 1.4 CE Compliance
      • 1.4.1 Design Guidelines
      • 1.4.2 Interfacing the Jackrabbit to Other Devices
  • 2. Getting Started
    • 2.1 Development Kit Contents
    • 2.2 Development Hardware Connections
      • 2.2.1 Attach Jackrabbit to PrototypingBoard
      • 2.2.2 Connect Programming Cable
      • 2.2.3 Connect Power
    • 2.3 Installing Dynamic C
    • 2.4 Run a Sample Program
      • 2.4.1 Troubleshooting
    • 2.5 Where Do I Go From Here?
      • 2.5.1 Real-Time Clock
      • 2.5.2 Technical Support
  • 3. Subsystems
    • 3.1 Jackrabbit Pinouts
      • 3.1.1 Headers
    • 3.2 Digital Inputs/Outputs
      • 3.2.1 Digital Inputs
      • 3.2.2 Digital Outputs
      • 3.2.3 Bidirectional I/O
    • 3.3 A/D Converter
    • 3.4 D/A Converters
      • 3.4.1 DA1
      • 3.4.2 DA0
    • 3.5 Serial Communication
      • 3.5.1 RS-232
      • 3.5.2 RS-485
      • 3.5.3 Programming Port
    • 3.6 Programming Cable
      • 3.6.1 Changing Between Program Mode and Run Mode
    • 3.7 Memory
      • 3.7.1 SRAM
      • 3.7.2 Flash EPROM
    • 3.8 Other Hardware
      • 3.8.1 External Interrupts
      • 3.8.2 Clock Doubler
      • 3.8.3 Spectrum Spreader
  • 4. Software Reference
    • 4.1 An Overview of Dynamic C
    • 4.2 Sample Programs
      • 4.2.1 DEMOJR1.C
      • 4.2.2 Other Sample Programs Illustrating Digital I/O
      • 4.2.3 RS-232 Serial Communication Sample Programs
      • 4.2.4 RS-485 Serial Communication Sample Program
    • 4.3 Cooperative Multitasking
      • 4.3.1 Advantages of Cooperative Multitasking
    • 4.4 Jackrabbit Function Calls
      • 4.4.1 I/O Drivers
      • 4.4.2 Serial Communication Drivers
    • 4.5 Upgrading Dynamic C
      • 4.5.1 Patches and Bug Fixes
      • 4.5.2 Add-On Modules
  • Appendix A. Specifications
    • A.1 Electrical and Mechanical Specifications
      • A.1.1 Exclusion Zone
      • A.1.2 Headers
    • A.2 Jumper Configurations
    • A.3 Conformal Coating
    • A.4 Use of Rabbit 2000 Parallel Ports
  • Appendix B. Prototyping Board
    • B.1 PrototypingBoard Overview
      • B.1.1 Prototyping Board Features
    • B.2 Mechanical Dimensions and Layout
    • B.3 Using the Prototyping Board
      • B.3.1 Demonstration Board
      • B.3.2 Prototyping Board
  • Appendix C. Power Management
    • C.1 Power Supplies
    • C.2 Batteries and External Battery Connections
      • C.2.1 Battery Backup Circuit
      • C.2.2 Power to VRAM Switch
      • C.2.3 Reset Generator
    • C.3 Chip Select Circuit
  • Index
  • Schematics