Document Outline

• FOREWORD
• SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS
  • Contact :
  • In USA:
  • Outside USA:
• REVISION LOG
• SECTION 1. SAFETY PRECAUTIONS
  • 1.1 GENERAL
  • 1.2 PRE-OPERATION
    • Operator Training And Knowledge
    • Workplace Inspection
    • Machine Inspection
  • 1.3 OPERATION
    • General
    • Trip and Fall Hazard
    • Electrocution Hazards
    • Tipping Hazard
    • Crushing And Collision Hazard
  • 1.4 Towing, Lifting, And Hauling
• SECTION 2. PREPARATION AND INSPECTION
  • 2.1 PERSONNEL TRAINING
    • Operator Training
    • Training Supervision
    • Operator Responsibility
  • 2.2 PREPARATION, INSPECTION, AND MAINTENANCE
  • 2.3 PRE-START INSPECTION
  • 2.4 DAILY WALK-AROUND INSPECTION
  • 2.5 Function Check
• SECTION 3. MACHINE CONTROLS, INDICATORS AND OPERATION
  • 3.1 GENERAL
  • 3.2 MACHINE DESCRIPTION
  • 3.3 MACHINE OPERATION
    • Getting Started
  • 3.4 BATTERY CHARGING
    • Battery - Low Voltage Warning Indicators
    • To Charge Batteries
    • Battery Charging Status Indicators
  • 3.5 GROUND CONTROL STATION - OPERATION
    • Main Power Selector Switch
    • Emergency Stop/Shut Down Button
    • Brake Release Button
    • Platform Up
    • Platform Down
    • Manual Descent Control Valve
    • Machine Status LCD Display
    • LCD Display Fault Conditions
  • 3.6 PLATFORM CONTROL CONSOLE OPERATION
    • General
    • Platform On/Off Key Switch
    • Platform Emergency Stop Button
    • Platform Control Display Panel
    • Drive/Lift Mode Selector Switch
    • Horn Button
    • Joystick Function Enable Lever
    • Multifunction Joystick Control
    • Drive Mode
    • Lift Mode
    • Drive Speed Setting Controls
  • 3.7 PARKING MACHINE
  • 3.8 PLATFORM CONFIGURATIONS
    • StockPicking Platform Operation
  • 3.9 FALL PROTECTION - LANYARD ATTACHMENT
  • 3.10 QUICK-CHANGE PLATFORM MOUNTING
    • Platform Removal (see illustration following)
    • Platform Installation
  • 3.11 TRANSPORTING, LIFTING AND TIE DOWN PROCEDURES
    • General
    • Truck Transport
    • Machine Tie-Down
    • Crane Hook Accessory (Option)
    • Fork-Lift Truck Transport
  • 3.12 PROGAMMABLE SECURITY LOCK (PSL™) (MVL/MSP - OPTION)
    • PSL™ Box and Ground Control Locations
    • Machine Power Up using the PSL™
    • Machine Power Down
    • Changing the Operator’s Code
  • 3.13 OBSTRUCTION SENSING SYSTEM - (MSP OPTION)
    • System Description
    • Operation
    • OSS Pre-Start Inspection
  • 3.14 RUG CARRIER ACCESSORY (MSP - OPTION)
    • General
    • Pre-Start Inspection
    • Hanging a Rug using the Rug Carrier Accessory Arms
    • Removing a Rug using Rug Carrier Accessory Arms
  • 3.15 STOCK-PICKER HANGER ACCESSORY
    • Pre-Start Inspection
    • Loading and Transporting an Item using the Hanger Accessory
• SECTION 4. EMERGENCY PROCEDURES
  • 4.1 GENERAL INFORMATION
  • 4.2 EMERGENCY OPERATION
    • Operator Unable to Control Machine
    • Platform Caught Overhead
  • 4.3 INCIDENT NOTIFICATION
• SECTION 5. GENERAL SPECIFICATIONS AND OPERATOR MAINTENANCE
  • 5.1 Introduction
  • 5.2 General Specifications
    • Machine Specifications
    • Machine Wheel Loads and PSI - Per Wheel
    • Electrical Specifications
    • Platform Data
    • Machine Component Weights
    • Serial Number Locations
  • 5.3 Operator maintenance
    • Battery
    • Tires and Wheels
    • Lubrication
  • 5.4 GROUND CONTROL STATION - PROGRAMMING
    • General
    • Programming Levels
    • Operator Programming Mode
    • Activating Programming Mode
    • Entering Password
    • Programming Mode Selection
    • Selecting Programmable Item to Adjust
    • Adjusting Programmable Setting
  • 5.5 DRIVE MOTOR BRUSH WEAR - WARNING INDICATION
  • 5.6 SUPPLEMENTAL INFORMATION
• SECTION 6. INSPECTION AND REPAIR LOG