Document Outline

• HMP60 AND HMP110 SERIES USER'S GUIDE
  • TABLE OF CONTENTS
  • GENERAL INFORMATION
    • About This Manual
      • Contents of This Manual
      • Version Information
      • Related Manuals
      • Documentation Conventions
    • Safety
    • ESD Protection
    • Recycling
    • Regulatory Compliances
    • Patent Notice
    • Trademarks
    • License Agreement
    • Warranty
  • PRODUCT OVERVIEW
    • Introduction to HMP60 and HMP110 Series
    • Basic Features and Options
      • Filter Options
    • Installation Accessories (Optional)
      • Probe Mounting Clamp
      • Probe Mounting Flange
      • Plastic Locking Bushing for HMP63 and HMP113
      • Duct Installation Kit for HMP60, HMP110 and HMP110T
      • Loop Power Converter
      • Cables
  • INSTALLATION
    • Dimensions for HMP60, HMP110 and HMP110T
    • Dimensions for HMP63 and HMP113
    • Mounting the HMP60, HMP110 and HMP110T Probes
      • Probe Assembly with Duct Installation Kit
      • Drilling Instructions for Duct Installation Kit
    • Mounting the HMP63 and HMP113 Probes
    • Wiring
      • Wiring with the Loop Power Converter
      • Power Supply Requirements
        • Recommendations
  • OPERATION
    • Getting Started
    • Serial Line Communication
      • Connecting to the Serial Interface
      • Installing the Driver for the USB Cable
      • Terminal Application Settings for Probes in RS-485 Mode
      • Terminal Application Settings for Probes in Analog Mode
    • List of Serial Commands
    • Device Information and Status
      • View Device Information
      • View Calibration Information
      • View Order Code
      • View Serial Number
      • View Software Version
    • Serial Line Output Commands
      • Start Measurement Output
      • Stop Measurement Output
      • Output the Measurement Message Once
    • Configuring Serial Line Operation
      • Set Serial Line Settings
      • Set Serial Interface Mode
      • Set Output Interval
      • Set Measurement Filtering
      • Set Probe Address
      • Set Serial Interface Delay
      • Set Measurement Units
    • Calibration Commands
      • Calibrate Humidity Measurement
      • Clear Adjustment of RH Measurement
      • Calibrate Temperature Measurement
      • Clear Adjustment of T Measurement
      • View User Adjustment Parameters
    • Other Commands
      • Set Analog Output Mode
      • Set Analog Output Parameters and Scaling
      • Extend Analog Output Range
      • Display Command List
      • Display the Currently Active Errors
      • Connect to the Probe in POLL Mode
      • Close the Connection in POLL Mode
      • Reset the Probe
      • Restore Factory Settings
  • MAINTENANCE
    • Periodic Maintenance
      • Cleaning
      • Changing the Filter
    • Calibration Procedure
    • Adjustment Procedure (HMP110 and HMP113)
      • One-Point Adjustment of RH Measurement (HMP110 and HMP113)
      • Two-Point Adjustment of RH Measurement (HMP110 and HMP113)
      • One-Point Adjustment of T Measurement (HMP110, HMP113, and HMP110T)
    • Repair Maintenance
      • Changing the INTERCAP® Sensor (HMP60 and HMP63)
      • Changing the HUMICAP® 180R Sensor (HMP110 and HMP113)
  • TROUBLESHOOTING
    • Solving Typical Problems
    • Technical Support
    • Product Returns
  • TECHNICAL DATA
    • Specifications
      • Performance (HMP60 and HMP63)
        • Relative Humidity
        • Temperature
        • Dewpoint
      • Performance (HMP110)
        • Relative Humidity
        • Temperature
        • Dewpoint
      • Performance (HMP113)
        • Relative Humidity
        • Temperature
        • Dewpoint
      • Performance (HMP110T)
        • Temperature
      • Operating Environment
      • Inputs and Outputs
      • Mechanics (HMP60, HMP110 and HMP110T)
      • Mechanics (HMP63 and HMP113)
    • Options and Accessories