Document Outline

• 1/4-DIN, 1/8-DIN & 1/16-DIN TEMPERATURE CONTROLLERS PRODUCT MANUAL
  • PREFACE
  • VOLUME 1 - OPERATING INSTRUCTIONS
    • OPERATOR MODE
      • INTRODUCTION
      • DISPLAYS AVAILABLE
        • Single Setpoint Operation
        • Dual Setpoint Operation
      • ADJUSTING THE SETPOINT/SETPOINT RAMP RATE
      • ALARM STATUS DISPLAY
      • OVER-RANGE/UNDER-RANGE DISPLAYS
      • SENSOR BREAK INDICATION
      • MANUAL CONTROL MODE
      • PRE-TUNE FACILITY
      • SELF-TUNE FACILITY
      • VIEWING THE HARDWARE DEFINITION CODE
    • SET UP MODE
      • ENTRY INTO SET UP MODE
      • SET UP MODE PARAMETERS
        • Input Filter Time Constant
        • Process Variable Offset
        • Output Power 1
        • Output Power 2
        • Proportional Band 1
        • Proportional Band 2
        • Reset (Integral Time Constant)
        • Rate (Derivative Time Constant)
        • Overlap/Deadband
        • Bias (Manual Reset)
        • ON/OFF Differential
        • Setpoint High Limit
        • Setpoint Low Limit
        • Recorder Output Scale Maximum
        • Recorder Output Scale Minimum
        • Output 1 Power Limit
        • Output 1 Cycle Time
        • Output 2 Cycle Time
        • Process High Alarm 1 Value
        • Process Low Alarm 1 Value
        • Band Alarm 1 Value
        • Deviation (High/Low) Alarm 1 Value
        • Process High Alarm 2 Value
        • Process Low Alarm 2 Value
        • Band Alarm 2 Value
        • Deviation (High/Low) Alarm 2 Value
        • Loop Alarm Enable
        • Loop Alarm Time
        • Scale Range Decimal Point
        • Scale Range Maximum
        • Scale Range Minimum
        • Auto Pre-Tune Enable/Disable
        • Manual Control Enable/Disable
        • Setpoint Ramp Enable/Disable
        • Setpoint Strategy
        • Communications Enable/Disable
        • Lock Value
      • OPERATOR MODE DISPLAYS
      • TUNING THE CONTROLLER MANUALLY
        • Controllers Fitted with Output 1 Only
        • Controllers Fitted with Output 1 and Output 2
      • SELF-TUNE AND PRE-TUNE FACILITIES
      • EXIT FROM SET UP MODE
    • RS485 SERIAL COMMUNICATIONS
      • COMMUNICATIONS ENABLE/DISABLE
      • PHYSICAL REQUIREMENTS
        • Character Transmission
        • Line Turn-Round
        • Communications Protocol
        • Type 1 Message
        • Type 2 Message
        • Scan Tables
        • Type 3 Message
        • Type 4 Message
      • INDIVIDUAL PARAMETERS
        • Input Parameters
          • Process Variable
          • Process Variable Offset
          • Scale Range Maximum
          • Scale Range Minimum
          • Input Filter Time Constant
        • Output Parameters
          • Power Output value
          • Output 1 Power Limit
          • Output 1 Cycle Time
          • Output 2 Cycle Time
          • Recorder Output Scale Maximum
          • Recorder Output Scale Minimum
        • Setpoint Parameters
          • Setpoint value
          • Setpoint Ramp Rate
          • Setpoint High Limit
          • Setpoint Low Limit
        • Alarm Parameters
          • Alarm 1 value
          • Alarm 2 value
        • Tuning Parameters
          • Rate (Derivative Time Constant)
          • Reset (Integral Time Constant)
          • Manual Reset (Bias)
          • ON/OFF Differential
          • Proportional Band 1 value
          • Proportional Band 2 value
          • Controller Status
          • Arithmetic Deviation
          • Scan Tables
        • Controller Commands
      • ERROR RESPONSE
    • Alphabetic Index - Volume 1
  • VOLUME 2 - INSTALLATION & CONFIGURATION INSTRUCTIONS
    • INSTALLATION
      • UNPACKING
      • PANEL-MOUNTING
      • CONNECTIONS AND WIRING
        • Mains (Line) Input
        • 24V (Nominal) AC/DC Supply
        • Thermocouple Input
        • RTD Inputs
        • Linear Inputs
        • Dual Setpoint Selection Input
        • Relay Outputs
        • SSR Drive Outputs
        • Solid State Outputs
        • DC Outputs
        • RS485 Serial Communications Link
    • INTERNAL LINKS AND SWITCHES
      • REMOVING THE CONTROLLER FROM ITS HOUSING
      • REMOVING/REPLACING THE OUTPUT 2/OUTPUT 3 OPTION PCBs
      • REMOVING/REPLACING THE RS485 COMMUNICATIONS OPTION PCB OR DUAL SETPOINT OPTION PCB
      • REPLACING THE CONTROLLER IN ITS HOUSING
      • SELECTION OF INPUT TYPE
        • 1/16 -DIN Controllers
        • 1/4-DIN and 1/8-DIN Controllers
      • SELECTION OF OUTPUT 1 TYPE
        • 1/16-DIN Controllers
        • 1/4-DIN and 1/8-DIN Controllers
      • OUTPUT 2 TYPE/OUTPUT 3 TYPE
    • CONFIGURATION MODE
      • ENTRY INTO CONFIGURATION MODE
      • HARDWARE DEFINITION CODE
      • OPTION SELECTION
      • CONFIGURATION MODE PARAMETERS
        • Input Range
        • Output 1 Action
        • Alarm 1 Type
        • Alarm 2 Type
        • Alarm Inhibit
        • Output 2 Usage
        • Output 3 Usage
        • Communications Baud Rate
        • Communications Address
        • Cold Junction Compensation Enable/Disable
        • Lock Code
      • ALARM HYSTERESIS OUTPUTS
      • EXIT FROM CONFIGURATION MODE
    • PRODUCT SPECIFICATION
      • UNIVERSAL INPUT
        • General
        • Thermocouple
        • Resistance Temperature Detector (RTD) and DC mV
        • DC Linear
      • DUAL SETPOINT SELECTION INPUT (OPTION)
      • OUTPUT 1
        • General
        • Relay
        • SSR Drive/TTL
        • Solid State
        • DC
      • OUTPUT 2
        • General
        • Relay
        • SSR Drive/TTL
        • Solid State
        • DC
      • OUTPUT 3
        • General
        • Relay
        • SSR Drive/TTL
        • Solid State
        • DC
      • LOOP CONTROL
      • ALARM CONTROL
      • PERFORMANCE
        • Reference Conditions
        • Performance Under Reference Conditions
        • Operating Conditions
        • Performance Under Operating Conditions
      • ENVIRONMENTAL
      • PHYSICAL
    • Alphabetic Index - Volume 2