Document Outline

• 1 Overview
  • 1.1 Structure and function
  • 1.2 Behaviour of the system to a power failure
• 2 Safety instructions
  • 2.1 User qualification
  • 2.2 Authorized use
  • 2.3 General safety instructions
• 3 Installation
  • 3.1 Scope of delivery
  • 3.2 Requirements of the measurement location
  • 3.3 Basics of the installation
    • 3.3.1 System planning
  • 3.4 Basic requirements for optimum installation
    • 3.4.1 General information
    • 3.4.2 Drawing up the power rating
    • 3.4.3 Optimum installation of the additional MIQ power supply module
  • 3.5 Installation guidelines for lightning protection
  • 3.6 Connecting system components
    • 3.6.1 Connecting MIQ modules: General information
    • 3.6.2 Variant 1: Stack expansion forwards
    • 3.6.3 Variant 2: stack expansion backwards
    • 3.6.4 Distributed mounting
    • 3.6.5 Connecting IQ sensors
  • 3.7 Onsite installation of DIQ/S 182 XT-4 and MIQ modules
    • 3.7.1 General information
    • 3.7.2 Mounting on a mounting stand with the SSH/IQ sun shield
    • 3.7.3 Mounting under the SD/K 170 sun shield
    • 3.7.4 Panel mounting
    • 3.7.5 Top hat rail mounting
  • 3.8 Using DIQ modules (accessories)
    • 3.8.1 DIQ/JB
    • 3.8.2 DIQ/CHV
    • 3.8.3 Installation of the DIQ modules
  • 3.9 Electrical connections: General instructions
  • 3.10 Connecting the voltage supply
    • 3.10.1 DIQ/S 182 XT-4 (line power version)
    • 3.10.2 DIQ/S 182 XT-4/24V (24 V version)
  • 3.11 Connections to the relay and current outputs
    • 3.11.1 General installation instructions
    • 3.11.2 Usage of the auxiliary voltage
  • 3.12 Commissioning
  • 3.13 Installation examples
    • 3.13.1 Connection of four sensors (without compressed air cleaning)
    • 3.13.2 Compressed air cleaning of two sensors
    • 3.13.3 Connection of a sensor that is located at a distance (without compressed air cleaning)
  • 3.14 Figures of the terminal strips
• 4 Operation
  • 4.1 Operating elements
  • 4.2 Measured value and status display
  • 4.3 Working with the SETTINGS menu
    • 4.3.1 Selection menus
    • 4.3.2 Setting tables
    • 4.3.3 Entry mode
  • 4.4 PROPERTIES menu
    • 4.4.1 Overview
    • 4.4.2 Maintenance condition
    • 4.4.3 Sensor status Sxx
  • 4.5 Calibration of sensors
  • 4.6 Passwords
• 5 The SETTINGS menu
  • 5.1 Overview of the SETTINGS menu
  • 5.2 Language
  • 5.3 Sensor S01 to S04
  • 5.4 Outputs D00 to Dxx
  • 5.5 System
• 6 Outputs
  • 6.1 Outputs of the system 182 XT-4
  • 6.2 Linking and adjusting: general procedures
    • 6.2.1 linking outputs
    • 6.2.2 Deleting a link with an output
    • 6.2.3 Setting outputs
  • 6.3 Basic information on relay functions
    • 6.3.1 Monitoring
    • 6.3.2 Limit indicator
    • 6.3.3 Proportional output
  • 6.4 Setting table for relays
    • 6.4.1 Functions and settings
    • 6.4.2 System monitoring
    • 6.4.3 Sensor monitoring
    • 6.4.4 Limit indicator
    • 6.4.5 Frequency output
    • 6.4.6 Pulse-width output
    • 6.4.7 Sensor controlled
    • 6.4.8 Cleaning
    • 6.4.9 Manual control
  • 6.5 Setting tables for current outputs
    • 6.5.1 Functions and settings
    • 6.5.2 Recorder
    • 6.5.3 PID controller
    • 6.5.4 Fixed current value
  • 6.6 Behavior of linked outputs
    • 6.6.1 Behavior in case of error
    • 6.6.2 Behavior in non-operative condition
• 7 Maintenance and cleaning
  • 7.1 Maintenance
  • 7.2 Cleaning
• 8 What to do if ...
  • 8.1 Information on errors
  • 8.2 Error causes and remedies
  • 8.3 Replacing system components
    • 8.3.1 Replacing passive components
    • 8.3.2 Adding and replacing IQ sensors
• 9 Technical data
  • 9.1 DIQ/S 182 XT-4
  • 9.2 MIQ modules
  • 9.3 DIQ/JB
  • 9.4 DIQ/CHV
  • 9.5 Space required by mounted components
• 10 Contact Information
  • 10.1 Ordering & Technical Support
  • 10.2 Service Information
• 11 Accessories and options
• 12 Index
• 13 Appendix (store separately if required)
  • 13.1 Forgotten the password?
  • 13.2 Default passwords