Mitsumi electronic WD-Y577 - Manual (Page 23)

3. TV Connections 23
Older Cable Box
Required: One coaxial cable
Note: This connection is not recommended. The
other connections described in this chapter
provide better quality audio and video to the TV
and allow NetCommand to work with the cable
box.
1. Connect the incoming cable to IN on cable box.
2. Connect one coaxial cable from OUT on the cable
box to ANT 1/MAIN on the TV back panel.
INPUT 1
INPUT 2
L ( MONO) R
AUDIO
DIGITAL
AUDIO
OUT HDMI 1 2
Y Pb Pr
AVR
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA / XGA / W-XGA / SXGA / 720p /1080p
IR EMITTER
NetCommand R
PC/DVI
AUDIO
INPUT
ANT 2 / AUX
ANT 1 / MAIN ANT 1 / MAIN
065
*/
  $BCMF
#PY
*ODPNJOH

$BCMF
5P
"/5
."*/
57
#BDL
1BOFM
Figure 12. Connecting an older cable box
A/V Receiver (Sound System)
Most setups require either a digital audio cable or
analog stereo audio cables.
The TV makes all audio available in digital and analog
formats:
Analog audio coming into the TV is available as
output in digital format on the DIGITAL AUDIO
OUT jack.
Digital incoming audio is available as analog
output on the AVR AUDIO OUTPUT/AUDIO L
(MONO) and AUDIO R jacks.
Usually, only one of the following connections is
required:
• To connect an analog A/V receiver
Connect left (white) and right (red) audio cables
from AVR AUDIO OUTPUT/AUDIO L (MONO) and
AUDIO R on the TV back panel to the TV AUDIO
INPUT on the A/V receiver.
• To connect a digital A/V receiver with Dolby
Digital surround sound and PCM audio support:
Connect one end of the digital audio cable
to
DIGITAL AUDIO OUT on the back of the TV.
Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V receiver.
INPUT 1
INPUT 2
L ( MONO) R
AUDIO
DIGITAL
AUDIO
OUT HDMI 1 2
Y Pb Pr
AVR
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA / XGA / W-XGA / SXGA / 720p /1080p
IR EMITTER
NetCommand R
PC/DVI
AUDIO
INPUT
ANT 2 / AUX
ANT 1 / MAIN DIGITAL
AUDIO
OUT
AVR
AUDIO
OUTPUT
%JHJUBM
$PBYJBM
$BCMF
6TF
UP
DPOOFDU
B

EJHJUBM
"7
SFDFJWFS
4UFSFP
"OBMPH
$BCMFT
6TF
UP
DPOOFDU
BO

BOBMPH
"7
SFDFJWFS
Figure 11. Connecting the TV to an A/V receiver
Important
A/V Receivers with HDMI Inputs
If your A/V receiver has an HDMI input, use
one of the audio connections described here
instead of an HDMI connection.
Note:
On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from
the TV as a digital signal. To hear these copy-
protected signals through the A/V receiver, use
connections for analog A/V receivers.
Check the A/V receiver’s Owner’s Guide for
information concerning use of the digital input
and switching between digital sound and
analog stereo sound from the TV.