MITSUBISHI ELECTRIC DX-NT400E - Manual (Page 47)

47
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations
ENGLISH
<INITIAL SET UP/INFORMATION>
♦ HDD REPEAT PLAY
This item is used to playback the recorded contents of the
HDD repeatedly.
<HDD SETTINGS>
HDD REPEAT REC MAIN ON
HDD REPEAT REC SUB OFF
>>HDD REPEAT PLAY OFF
IM-CHECK PLAY OFF
SEQUENTIAL PLAY OFF
Setting (default: “OFF”)
“ON”: Automatically resumes playback from the
beginning of the recorded data when the recorded
data is played back to the end.
“OFF”: Stops playback when the recorded data is
played back to the end.
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select “HDD REPEAT PLAY” in the
<HDD SETTINGS> screen. Display the desired setting and
determine such setting.
2. Press the CLEAR button or the SET UP button.
♦ IM-CHECK PLAY
This item is used to check whether the recorded video or
the recording date/time is altered.
<HDD SETTINGS>
HDD REPEAT REC MAIN ON
HDD REPEAT REC SUB OFF
HDD REPEAT PLAY OFF
>>IM-CHECK PLAY OFF
SEQUENTIAL PLAY OFF
Setting (default: “OFF”)
“ON”: Executes alteration check during playback and
displays a warning at the point of alteration.
“OFF”: Does not execute alteration check.
This function may cause problems during record-
ing and playback. Normally, set this function to “OFF.”
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select “IM-CHECK PLAY” in the <HDD
SETTINGS> screen. Display the desired setting and determine
such setting.
2. Press the CLEAR button or the SET UP button.
3. Select the HDD to execute alteration check and then start
playback.
Warning is also displayed for the portion where
the recorded data is damaged for some reason.
■ HDD SETTINGS
♦ HDD REPEAT REC MAIN/HDD REPEAT REC
SUB
This item is used to set the operation when HDD space
becomes full during recording.
<HDD SETTINGS>
>>HDD REPEAT REC MAIN ON
HDD REPEAT REC SUB OFF
HDD REPEAT PLAY OFF
IM-CHECK PLAY OFF
SEQUENTIAL PLAY OFF
“HDD REPEAT REC SUB” appears when “HDD
SETTING” in <INITIALIZATION> screen is set to
“PARTITION.”
Setting (default of HDD REPEAT REC MAIN: “ON,”
default of HDD REPEAT REC SUB: “OFF”)
“ON”: Automatically returns to the beginning of the
HDD and resumes recording (by overwriting the
existing data).
“STANDBY”: Stops recording and switches to the
standby mode. Recording resumes when both REC/
STOP buttons are pressed. Recording pauses when
the alarm input is continuously grounded or during
timer recording, then, recording resumes from the
beginning of the HDD.
“OFF”: Stops recording and “REC/FULL” or “REC/
SUB FULL” appears on the screen. To resume
recording, press and hold the WARNING RESET
button for more than 3 seconds to clear the “REC/
FULL” or “REC/SUB FULL” display and then press
both REC/STOP buttons.
When an error occurs to one HDD and another
HDD does not affected by this error, the recording
continues with another HDD.
“STANDBY” is displayed only in “HDD REPEAT
REC MAIN.”
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select “HDD REPEAT REC MAIN” or
“HDD REPEAT REC SUB” in the <HDD SETTINGS> screen.
Display the desired setting and determine such setting.
2. Press the CLEAR button or the SET UP button.