Sony 5500 - Manual (Page 63)

63
4-3 TC Menu
C
h
ap
te
r 4
M
enu
Se
tt
in
g
s
STARTING TC: Time code used as a reference when
converting time code.
JUMPING TC: The loopback point for converting
time code with STARTING TC as the reference
point, and the conversion done in both forward
and reverse directions.
The time code is discontinuous at this point.
The following table shows an example of how the 25 frame
time code is discontinuous when the operating frequency
is 25PsF, the playback tape is 24 frames, and STARTING
TC is 01:00:00:00, and 24F JUMPING TC 22:00:00:00
(JUMP TC SEL=–3H).
3
If necessary, use the function buttons to change the
settings.
For details on the settings made by these buttons, see
the following table.
To preset the 24F STARTING TC using the
numeric buttons
1
Press the TC button, and then press the ALT button.
The ALT+TC menu appears.
2
Press the [F3] (TCCONV MENU) button.
The TC CONVERT menu appears.
3
Enter the time code in the data entry window with the
numeric buttons.
4
Press the SET button to set the time code.
24 Frames TC 25 Frames TC
JUMPING TC 22:00:00:00 20:09:36:00
: :
01:00:01:01 01:00:01:00
Forward direction 01:00:01:00 01:00:00:24
M : :
STARTING TC 01:00:00:00 01:00:00:00
m 00:59:59:23 00:59:59:24
Reverse direction : :
22:00:00:01 22:07:12:01 Non-
consecutive
part
JUMPING TC 22:00:00:00 21:09:36:00
Button Indication Function
[F3] TC CONV Specifies whether the time code
is converted to time code or not.
[F4] ORG TC DISP Specifies whether the time code
is displayed or not on two lines
in the HOME, TC, and PF
menus along with the converted
time code.
[F6] START TC PST Press to preset the STARTING
TC using the numeric buttons.
T C
C O N V
o n
O R G T C
d i s p
o n
S T A R T
T C E N T
J U M P
T C S E L
+ 3 H
E X I T S T A R T
T C P S T
00
H
00
M
00
S
00
F
S T A R T I N G T C
03
H
00
M
00
S
00
F
J U M P I N G T C
00
H
00
M
00
S
00
F
C U R R E N T T C
[F7] START TC ENT Press to enter the current time
code as the STARTING TC.
[F8] JUMP TC SEL Selects the JUMPING TC as an
interval from STARTING TC.
Selectable values: –3H, –2H,
–1H, +1H, +2H, +3H, 0H
[F10] EXIT Select to exit the TC CONVERT
menu.
Button Indication Function
4 1 2
3
T C C O N V
M E N U
o n
O R G T C
D I S P
o n
S T A R T
T C E N T
J U M P
T C S E L
- 3 H
E X I T S T A R T
T C P S T
S T I L L
0 1 0 0 0 0 0 0
S S
H D C A M - S R
R E M A I N : 0 1 H 0 6 M
! A L T + T C
00
H
00
M
00
S
00
F
S T A R T I N G T C
03
H
00
M
00
S
00
F
J U M P I N G T C
00
H
00
M
00
S
00
F
C U R R E N T T C
Data entry window