Samson EXL250 - Manual (Page 16)

Expedition Express Input and Output Connectors
Line Level Input - Mono Input Channels 1, 2
Use these inputs to connect synthesizers, drum
machines, effects processors or any line-level signal.
The LINE inputs have a nominal operating level of
-40dB through - 10dB. TRS phone jacks Connector
pin-out - Sleeve: Ground, Tip: Hot (+), Ring: Cold (-)
Microphone Input - Mono Input Channels 1, 2
Use these inputs to connect Low Impedance micro-
phones and low level signals from direct boxes. The
MIC inputs have a nominal operating level of –50dB
through -20dB. The MIC inputs also feature +24V
phantom power, allowing you to use condenser
microphones. XLR Connector pin-out - Pin 1: Ground,
Pin 2: Hot (+), Pin 3: Cold (-)
Line Level Input - Stereo Input Channels 3/4
The Expedition Express’ stereo channel has a stereo
LINE input. You can connect the outputs from ste-
reo devices such as synthesizers, drum machines,
effects processors or any stereo line-level signal. The LINE inputs have a nominal operating level of -40dB
through - 10dB. TRS phone jacks Connector pin-out - Sleeve: Ground, Tip: Left, Ring: Right.
Microphone Input - Mono Input Channels 3/4
The Expedition Express’ stereo channel has a utility MIC input located on the XLR connector. The util-
ity MIC input has a nominal operating level of –50dB through -20dB. The MIC input also features +24V
phantom power, allowing you to use condenser microphones. XLR Connector pin-out - Pin 1: Ground,
Pin 2: Hot (+), Pin 3: Cold (-)
CD Input
The Expedition Express includes an input for connecting a CD player, cassette recorder, Mini Disk, or even
audio from a VCR. The CD input connectors are industry standard RCA connectors.
Extension Speaker Out
The Extension speaker output is used to connect the EXL250m powered speaker to the EXL250e exten-
sion speaker. Connect the supplied speaker cable from the EXT SPEAKER OUT connector to the SPEAKER
INPUT JACK located on the back of the EXL250e extension speaker.
NOTE: The EXL250e Extension Speaker has been designed for maximum performance with the EXL250m
Powered Speaker, therefore it is not recommend to use any other extension speaker for optimum perfor-
mance. When connecting an extension speaker to the EXL250m’s EXT SPEAKER OUT other than the EXL250e,
be sure that the total impedance of the extension speaker is no more that 8 Ohms. Connecting an Extension
speaker or speakers with a total impedance less than 8 Ohms, such as 4 or 2 Ohms (the lower the number, the
lower the impedance) may result in damage to the systems.
1
2
4
5
6
3
-15dB +15dB
HIGH
0 1
-15dB +15dB
LOW
0
0 10
REVERB
5
5
PAN
0 10
VOLUME
CH1 CH2 CH3/4
LINE IN
MIC INPUT CH1 MIC INPUT CH2 MIC INPUT CH3/4
WIRELESS IN
LINE IN LINE IN
5
0 10
VOLUME
5
0 10
VOLUME
VOLUME
CD IN
LIMITER
FUSE: T3.15AL 250V
AC IN
L
R
MAIN SPK RIGHT OUT
-15dB +15dB
HIGH
0 0 2
-15dB +15dB
LOW
0
0 10
REVERB
5
PAN
-15dB +15dB
HIGH
3/4
-15dB +15dB
LOW
0
0 10
REVERB
5
0 10
5
BALANCE
m
UTILISER UN FUSIBLE
DE RECHANGE DE
MEME TYPE.
CAUTION:
ATTENTION:
FOR CONTINUED
PROTECTION
AGAINST RISK
OF FIRE,
REPLACE ONLY
WITH SAME
TYPE OF FUSE.
5
OFF
4
10
6
1
3
9
7
2 8
1. MEDIUM BRIGHT PLATE
2. BEST PLATE
3. MEDIUM DARK SPRING
4. SHORT PLATE
5. LONG BRIGHT SPRING
6. SLAPBACK 2
7. SLAPBACK w/VERB
8. ECHO LONG VERB
9. SLOW ST CHOR
10. BEST HALL 2
DSP EFFECTS
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES
CLASS B. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS:(1) THIS DEVICE MUST NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION. SUITABLE FOR HOME
OR OFFICE USE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RATING
POWER 100-240 V ~ 50Hz/60Hz 360W
POWER
AC
ON
CHARGE
BATTERY OPERATION
OFF
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
AVIS;
MADE IN CHINA
1
2
3
5
6
4
Controls and Functions
INPUT AND OUTPUT CONNECTORS
ENGLISH
12