Sanyo VCC-MC600P - Manual (Page 20)

Camera Settings (CAMERA)
19
Switches automatically between color mode and black and white
mode depending on the luminance of the object being
monitored. This function lets you set the filming mode to color
mode during times of normal brightness like daytime or to black
and white mode during times of darkness like night.
• Enabling the Day/Night function (AUTO)
• Using the color mode only (COLOR)
• Using the black and white mode only (B/W)
b Setting the Day/Night function (AUTO)
This function automatically switches between the color mode and the
black and white mode according to the luminance of the target object.
The color mode is used for daytime; the black and white mode is
used for night.
1 Use the joystick lever (xy) to select [DAY/NIGHT],
use the lever (vw) to select “AUTO y”, and press
the [ENTER] button.
The D/N SETTING-AUTO screen appears.
2 Use the joystick lever (xy) to select [LEVEL], use
the lever (vw) to select a luminance level where the
viewing mode between the color mode and black
and white mode is switched, and press the [ENTER]
button.
Available settings:
• MID: The mode switches when the luminance of the
objects being monitored is between the “LOW” and
“HIGH” levels.
• HIGH: The mode switches when the luminance of the
objects being monitored is comparatively bright (the
black and white mode is used longer).
• ADJy: Sets the switching luminance level manually.
When you select “ADJy”, the LEVEL SETTING
screen appears allowing you to perform manual
settings for the switching luminance level.
• LOW: The mode switches when the luminance of the
objects being monitored is comparatively dark (the
color mode is used longer).
1 COLOR → B/W
Sets the luminance level for switching from the color mode
to the black and white mode.
Available settings: 1 - 7 (The larger the value, the darker
the switching luminance level.)
2 B/W → COLOR
Sets the luminance level for switching from the black and
white mode to the color mode.
Available settings: 1 - 7 (The larger the value, the
brighter the switching luminance
level.)
Memo: • In the “ADJ” setting, changing the setting for one of the
switching level settings (from color mode to black and
white mode or from black and white mode to color mode)
causes the other setting to change also.
• Increasing the luminance level difference avoids hunting
under IR (infrared) lighting.
I Setting the Day/Night function (DAY/NIGHT)
• A sound from the camera may be heard when the
color image or black and white image is switched.
Also, the image will be distorted as shown in the
figure below. This is normal and does not indicate a
problem.
• If the power is turned off in the black and white mode
and the power is turned on again, the color mode will
be used. The focused position may be differently
adjusted between the color mode and the black and
white mode. Adjust focusing so that the focused
position matches between the color mode and the
black and white mode.
• When using infrared lighting in black and white mode,
if there is a strong reflection on the subject, the black
and white mode may switch to color mode. Use only
enough infrared lighting so that the mode is not
switched.
y
y
y
y
y
SYNC
IRIS
WHITE BALANCE
BLC
SHUTTER
APERTURE
AGC
GAMMA
DAY/NIGHT
PRESET
MENU
INT
AUTO
ATW
OFF
OFF
ON
ON
0.45
AUTO
OFF
BACK
D/N SETTING-AUTO
LEVEL
BURST
FOCUS
MID
OFF
2
LEVEL SETTING
[COLORwB/W]
1
[B/WwCOLOR]
1
1
2
<The LEVEL SETTING screen under the “ADJ” option>
(For VCC-MC600P only)
L5BU2_XE(VCC-MC600P_MC500P)(GB).book 19 ページ ２００７年１月１８日 木曜日 午前９時４４分