Kenwood HM-381MD - Manual (Page 27)

HM-381MD (En)
27
Basic section
A tip for use of the tape counter
The tape counter is set to “0000” when a cassette tape is
loaded.
By writing down the counter reading in case you want to
interrupt recording (playback) in the middle of the tape,
the memo will be helpful as a reference for locating the
same position when continuing the recording (playback)
the next time. The tape counter figure decrements dur-
ing recording or playback of the back side (while the
2
tape transport indicator is lit).
To set the tape counter
to “0000”, open the cas-
sette holder once.
Then the counter will be
reset.
1Select “TAPE RVS. ?”.
2 Select.
3 Set it.
AM
8 4 5
AM
0 0 0 0
Let's put out some sound
To wind tape at high speed
÷ Press the 7 key to stop fast winding.
To fast wind in
direction
|
To fast wind in
direction
\
To stop playback
÷ Do not take out the cassette
tape until the tape transport
has stopped completely.
Selection of reverse mode
(Main unit only)
( Press the “set/demo” key while the “?” mark is
blinking.)
Tape counter display (Remote control unit only)
Each press of the TIME key changes the dis-
played contents.
÷ Normal (TYPE ), high (TYPE ), or metal (TYPE ) tape
selection is set automatically.
÷ Remove tape slack before loading.
÷ Close the door securely.
Lights
Reverse mode indication
Displayed when the deck is loaded with a tape.
1
2
(Time display)
(Tape count)
“ ”: (ONE-WAY)
Only one side is
played back (re-
corded), and then
the tape stops.
“ ” : (REVERSE)
Both sides are played back (recorded), and
then the tape stops.
“ ”:
(ENDLESS)
Both sides are
played back
endlessly.
(The tape stops
after recording
onto both sides.)
Selection of TAPE equalizer (TAPE EQ.)
(Remote control unit only)
When playing a tape prerecorded with Noise
Reduction system (such as the DOLBY NR) ON, be
sure to set the "tape EQ." ON for playback.
Each press switches the modes as follows.
1 “tape EQ.” ON ......... TAPE equalizer is used.
2 “tape EQ.” OFF ....... TAPE equalizer is not used.
Lit when “tape EQ.” is ON
÷ Select the "tape EQ." ON mode according to the
recording condition of the tape.
T.E.
Initial setup
do
wn up
VOLUME / multi control
T A P E • • S T O P •
STEREO
MD EDIT
TITLE SEARCH
FM
PM
AM
MHz
kHz
O.T.E.
TUNED
RANDOM PGM REPEAT ALL SLEEP A.P.S. O.T.T. PROG.
TP
R·D·S EON EON
T.E. NR
AUTO TOTAL TRACK NO.
8 8 8 8 0 0 0 0
1 2
TA PTY
1 ¡
T A P E • • S T O P •
STEREO
FM
PM
AM
MHz
kHz
TUNED AUTO TOTAL TRACK NO.
8 8 8 8 0 0 0 0
STOP
7
menu
set/demo
VOLUME / multi control
set/demo
T A P E • • P L A Y •
STEREO
MD EDIT
TITLE SEARCH
FM
PM
AM
MHz
kHz
O.T.E.
TUNED
RANDOM PGM REPEAT ALL SLEEP A.P.S. O.T.T. PROG.
TP
R·D·S EON EON
T.E. NR
AUTO TOTAL TRACK NO.
8 8 8 8 0 1 5 2
1 2
TA PTY
TAPE EQ.