Panasonic AJ-HD1800P - Manual (Page 110)

110
Setup menus
(continued)
<DIF>
*1 When the 23/24 Hz mode, 25 Hz (HD, SD) mode, or the 50 Hz
(HD, SD) mode is selected in System Menu No. 25 (SYSTEM
FREQ), this item is not displayed.
The underlining (__) denotes the factory setting mode.
No./Item Description of setting
880* 1
DIF SPEED
For setting the transfer speed of the IEEE1394
digital interface output.
0000 S100
100Mbps
0001 S200
200Mbps
0002 S400
400Mbps
<Note>
When S100 has been selected as this item’s setting,
DVCPRO HD format signals cannot be input or
output.
882*
1
DIF IN CH
For setting the input channel.
0000 0
: :
0063 63
The input channel is fixed at the channel
corresponding to the number specified.
0064 AUTO
The input channel is not fixed at the channel
corresponding to the number specified. The input
channel is initialized to 63 when the power is
turned on.
883* 1
DIF OUT CH
For setting the output channel.
0000 0
: :
0063 63
The input channel is fixed at the channel
corresponding to the number specified.
0064 AUTO
The output channel is not fixed at the channel
corresponding to the number specified. The output
channel is initialized to 63 when the power is
turned on.
886* 1
DIF CONFIG
Menu item for expansion purposes. Normally,
use DFLT as the setting.
0000 DFLT
0001 1
: :
0255 255
890* 1
DIF AUD
OUT
For setting the audio channels to which the
signals from the IEEE1394 digital interface are to
be output in the DV format when a DVCPRO HD
tape or 50M format tape is played back or when a
DV tape in 4ch mode is played by the audio
signals and menu No. 891 DIF DV AUDIO is set to
“LOCK48.”
0000 CH1/2
CH1 and CH2
0001 CH3/4
CH3 and CH4
891*
1
DIF DV
AUDIO
For setting forcible audio mode conversion when a
DV tape is played back and the audio signals are
output in the DV format.
0000 THRU
Normal setting (the signals simply pass through).
0001 LOCK
Forcible conversion to the LOCK mode (no
frequency conversion)
0002 LOCK48
Forcible conversion to 48kHz/2CH/LOCK.
No./Item Description of setting
892* 1
DIF SIG CMD
For setting how to reply when signals requesting
a confirmation of the format is sent from an
external device connected by the IEEE1394
digital interface.
0000
50M
DVDPRO50 is forcibly returned.
0001 25M
DVDPRO is forcibly returned.
0002 DV
DV is forcibly returned.
0003 AUTO
The reply is the same format as the signal format
output from the IEEE1394 digital interface.
<Note>
When the unit is connected to a non-linear editing
system using 50M, 25M, and DV signal format, the
non-linear editing system may not operate properly.
In this case, change the setting to return format
information corresponding to the connected signal
format in this menu and then start the system.
894*
1
HD > DIF
OUT
For setting the format of the signals to be output
from the IEEE1394 digital interface in the EE
mode, in recording or when a DVCPRO HD tape is
played back.
0000
HD
DVCPRO HD
0001 50M
DVCPRO50
0002 DV
DV
<Note>
When SD SDI is selected in Setup menu No. 600
(VIDEO IN SEL) and cross-conversion is provided,
data will be output in the format selected in Setup
menu No. 020 (SYS FORMAT) regardless of this
menu selection.
895* 1
50M > DIF
OUT
For setting the format of the signals to be output
from the IEEE1394 digital interface when a 50M
format tape is played back.
0000
50M
DVCPRO50
0001 DV
DV
<Note>
When DV is selected as this item’s setting, the closed
caption signals and time code (VITC) signals in the
vertical blanking period are transmitted, but none of
the other signals in the vertical blanking period are
transmitted.
896* 1
25M > DIF
OUT
For setting the format of the signals to be output
from the IEEE1394 digital interface when a 25M
format tape is played back.
0000
25M
DVCPRO
0001 DV
DV
899*
1
DIF SUPER
For setting whether the superimposed display is
to be output from the IEEE1394 digital interface
when the format is converted (from HD to 50M,
from HD to DV, from 50M to DV or from 25M to
DV).
0000
OFF
The superimposed text is not displayed.
0001 ON
The superimposed text is displayed.
<Note>
Only TCR is displayed.