Panasonic AJ-HD1800P - Manual (Page 88)

88
Setup menus
(continued)
<OPERATION> (continued)
Description of MEMORY STOP function
! If the FF button is pressed, the normal FF operation is
performed since there is no 0 point in the direction of this
operation.
@ If the REW button is pressed, the PREROLL lamp lights (as
does the SHTL lamp), the VTR prerolls the tape, and it
automatically stops when the counter value is at the 0 position.
# If the REW button is pressed, the normal REW operation is
performed since there is no 0 point in the direction of this
operation.
$ If the FF button is pressed, the PREROLL lamp lights (as does
the SHTL lamp), the VTR prerolls the tape, and it
automatically stops when the counter value is at the 0 position.
*1: When the 23/24 Hz mode, 25 Hz (HD, SD) mode, or 50 Hz
(HD, SD) mode is selected in System Menu No. 25 (SYSTEM
FREQ), this item is not displayed.
Accidental erasure protection function
This function is used to prevent parts already recorded on a tape
from being recorded over. Accidental erasure of pre-recorded
tapes is prevented by positioning the CTL signal rec/play heads as
shown in the figure below so that whether a recording has been
made can be determined by the presence or absence of the CTL
signal. When the REC/PLAY button is pressed with a pre-
recorded tape, the tape runs but the REC button lamp blinks, the
beeping alarm is sounded, and no signals are recorded.
No./Item Description of setting
111* 1
MEMORY
STOP
For selecting whether to automatically stop the
VTR when the counter value is at the “0”
position during CTL mode FF and REW
operations.
0000
OFF
The VTR does not stop.
0001 ON
The VTR is automatically stopped.
<Notes>
z Either the stop or still picture (SHTL STILL or
SLOW STILL) mode, whichever has been set
using setup menu item No.307 (AFTER CUE-
UP), is established when the VTR is stopped.
z If both the AUTO REW function and MEMORY
function have been selected at the same time,
the AUTO REW operation takes priority.
112
FRZ MODE
SEL
For selecting what playback images are to be
output in the STANDBY OFF (HALF LOADING)
mode and EJECT mode.
0000
DIS
The video output is muted.
0001 STB OFF
Only when the STANDBY OFF mode is estab-
lished is the image which was being played back
at that moment frozen and output.
0002 SOF&EJ
When either the STANDBY OFF mode or the
EJECT mode is established, the image which
was being played back at that moment is frozen
and output.
<Notes>
z The status when the picture is frozen is
determined by the setup menu item No.604
(FREEZE SEL) setting.
z In the EJECT mode, the frozen picture is output
only when 1 (BLACK) or 2 (GRAY) has been
selected as the setup menu item No.106 (EJECT
EE SEL) setting.
z When the 720/24p over 60p source is used and
the 23/24 mode is selected in System Menu item
No. 25 (SYSTEM FREQ), playback cannot be
frozen in EJECT mode.
1
2
3
4
The MEMORY STOP function does
not work if this margin is less than 0
d2 frames.
0 point
REW button
FF button REW
button
FF button
No./Item Description of setting
113 *1
REC INH
For selecting whether to allow or inhibit
recording on the cassette tape.
0000
OFF
Recording on the cassette tape is enabled when
the cassette’s accidental erasure prevention
mechanism has been set to the recording enable
position.
0001 ALL
All recording on the cassette tape is inhibited.
0002 PRE
Overwriting is inhibited during normal recording.
This is the setting to activate the accidental
erasure prevention function. While CTL is
detected, the recording is inhibited, and when
CTL cannot be detected, it is executed.
0003 NORM
Normal recording is inhibited.
Use this setting when it is preferable to avoid
using normal recording in all applications except
for editing.
0004 V/CTL
The recording of the video and CTL signals is
inhibited.
Use this setting when it is preferable to avoid
editing in all applications except for audio editing.
<Note>
When the PRE, NORM or V/CTL setting has been
selected, the REC INHIBIT lamp blinks (on for
approx. 0.5 sec. and then off for approx. 0.5 sec.).
114
REC INH
LAMP
For selecting whether the REC INHIBIT lamp is to
blink or light when the cassette tape has been set
to the accidental erasure protection mode.
0000
LIGHT
The lamp lights.
0001 FLASH
The lamp blinks.
<Note>
When Setup Menu No. 113 (REC INH) is set to
[ALL], the REC INHIBIT LAMP always lights
regardless of the setting.
115 *1
EJECT SW
INH
For selecting whether to enable or disable the
operation of the EJECT button on the VTR’s
front panel.
0000
REC
Operation is disabled while the VTR is in the
recording mode.
0001 OFF
Operation is enabled in all modes.
116
EJECT LAMP
For selecting whether the EJECT lamp is to
remain lighted or go off after the cassette tape
has been ejected.
0000
MODE1
The EJECT lamp remains lighted.
0001 MODE2
The EJECT lamp goes off.
A/C heads
(rec/play heads)
PRE CTL
head
Rough sketch showing CTL head positions