Panasonic AJ-HD1800P - Manual (Page 91)

91
Setup menus
(continued)
<EDIT>
*1 When the 23/24 Hz mode, 25 Hz (HD, SD) mode, or 50 Hz
(HD, SD) mode is selected in System Menu No. 25 (SYSTEM
FREQ), this item is not displayed.
The underlining (__) denotes the factory setting mode.
No./Item Description of setting
300
IN/OUT DEL
For selecting the operation to be performed
when an edit point has been set incorrectly
(when the OUT point comes before the IN
point).
0000 MANU
Editing is not performed unless the illegal edit
point is cleared or set properly.
0001 AUTO
The edit point which had already been input is
cleared automatically.
301
NEGA FLASH
For selecting whether to show a negative
display (time code display area) when the IN
point is greater than the OUT point.
0000 OFF
A negative display is not shown.
0001 ON
A negative display is shown.
302* 1
CONFI EDIT
For selecting whether to perform simultaneous
playback during editing.
0000 OFF
Simultaneous playback is not performed.
0001 ON
Simultaneous playback is performed.
<Note>
Regardless of the settings in Setup Menu No. 140
(OUTPUT), simultaneous playback is always
performed during editing.
303 *1
AUD EDIT
IN
For selecting how to connect the digital audio
edit IN points.
0000 CUT
Cut processing
0001 FADE
V-fade processing
304 *1
AUD EDIT OUT
For selecting how to connect the digital audio
edit OUT points.
0000 CUT
Cut processing
0001 FADE
V-fade processing
305
AUTO ENTRY
For selecting whether to register the IN points
using the PREROLL button in cases where the
IN points have not been registered.
0000 DIS
The IN points are not registered.
0001 ENA
The IN points are registered
306
*1
CF ADJ SEL
For selecting the deck whose the color framing
is to be adjusted during deck-to-deck editing.
0000 PLAYER
The player’s IN and OUT points are adjusted
(using the recorder as the reference).
0001 RECORD
The recorder’s IN and OUT points are adjusted
(using the player as the reference).
307
AFTER
CUE-UP
For selecting the VTR’s mode upon completion
of the cue-up operation.
0000 STOP
The VTR is set to the STOP mode.
0001 STILL
The VTR is set to the still picture (SHTL STILL)
mode.
0002 STILL2
The VTR is set to the still picture (SLOW STILL)
mode.
No./Item Description of setting
308
VAR FWD MAX
For setting the maximum speed of SLOW FWD.
0000 +4.9
i4.9 times normal tape speed
0001 +2
i2 times normal tape speed (i1.85 times
normal tape speed for formats other than
DVCPRO HD-LP)
0002 +1
i1 times normal tape speed
<Notes>
z At any setting other than 0 (i4.9), phase
adjustments cannot be conducted from the
editing controller.
z Depending on the format used, the actual tape
running speed differs slightly from what is
indicated by the superimposed display.
309
VAR REV MAX
For setting the maximum speed of SLOW REV.
0000 -4.9
j4.9 times normal tape speed
0001 -2
j2 times normal tape speed (j1.85 times
normal tape speed for formats other than
DVCPRO HD-LP)
0002 -1
j1 times normal tape speed
<Note>
Depending on the format used, the actual tape
running speed differs slightly from what is indicated
by the superimposed display.
310
JOG FWD
MAX
For setting the maximum speed of JOG FWD.
0000 +4.9
i4.9 times normal tape speed
0001 +2
i2 times normal tape speed (i1.85 times
normal tape speed for formats other than
DVCPRO HD-LP)
0002 +1
i1 times normal tape speed
<Note>
At any setting other than 0 (
i4.9), phase
adjustments cannot be conducted from the editing
controller which performs these adjustments by the
JOG command.
311
JOG REV MAX
For setting the maximum speed of JOG REV.
0000 -4.9
j4.9 times normal tape speed
0001 -2
j2 times normal tape speed (j1.85 times
normal tape speed for formats other than
DVCPRO HD-LP)
0002 -1
j1 times normal tape speed
312*
1
POSTROLL
TM
For setting the postroll time.
Any time from 0 to 5 seconds can be set in 1-
second increments.
0000 0s
0001 1s
0002 2s
0003 3s
0004 4s
0005 5s