Panasonic AJ-HD1800P - Manual (Page 134)

134
RS-232C interface
(continued)
5.Command table
_Commands relating to operation control
<Notes>
z As the return (completion) message, [ACK] is returned
when data is received, and only the execution message
which is subsequently returned is listed in the table.
z If a command not listed in the table is received, ER001
(invalid command) is returned after [ACK].
VTR
operation
Send command
Return (completion)
message
STOP [STX] OSP [ETX] [STX] OSP [ETX]
This command is for stopping the tape transport. The
resulting output picture and sound statuses differ
according to the setting selected for the setup menu
item No.105 (AUTO EE SEL).
For details, refer to the setup menus.
EJECT [STX] OEJ [ETX] [STX] OEJ [ETX]
This command is for ejecting the cassette tape. The
resulting output picture and sound statuses differ
according to the setting selected for the setup menu
item No.105 (AUTO EE SEL).
For details, refer to the setup menus.
PLAY [STX] OPL [ETX] [STX] OPL [ETX]
This command is for starting playback.
REWIND [STX] ORW [ETX] [STX] ORW [ETX]
This command is for rewinding the tape. The
resulting output picture and sound statuses differ
according to the setting selected for the setup menu
item No.105 (AUTO EE SEL).
The maximum speed differs according to the setting
selected for the setup menu item No.102 (FF. REW
MAX).
For details, refer to the setup menus.
FAST
FORWARD [STX] OFF [ETX] [STX] OFF [ETX]
This command is for fast forwarding the tape. The
resulting output picture and sound statuses differ
according to the setting selected for the setup menu
item No.105 (AUTO EE SEL).
The maximum speed differs according to the setting
selected for the setup menu item No.102 (FF. REW
MAX).
For details, refer to the setup menus.
REC [STX] ORC [ETX] [STX] ORC [ETX]
This command is for starting recording.
VTR
operation
Send command
Return (completion)
message
SHTL
FORWARD [STX] OSF:data [ETX] [STX] OSF [ETX]
This is the forward direction shuttle command.
data =
n:speed data
0:STILL
1:
k0.03
2: k0.1
3: k0.2
4: k0.5
5: k1
6: k2.0
(1.85 k for formats other than
DVCPROHD-LP)
7: k4.9
8: k9.8
9: k16
A: k32
<Note>
The 16
k and 32 k speeds differ according to the
setting selected for setup menu item No.101 (SHTL
MAX).
SHTL
REVERSE [STX] OSR:data [ETX] [STX] OSR [ETX]
This is the reverse direction shuttle command.
data =
n:speed data
0:STILL
1:
k0.03
2: k0.1
3: k0.2
4: k0.5
5: k1
6: k2.0
(1.85 k for formats other than
DVCPROHD-LP)
7: k4.9
8: k9.8
9: k16
A: k32
<Note>
The 16
k and 32k speeds differ according to the
setting selected for setup menu item No.101 (SHTL
MAX).
STANDBY
OFF [STX] OBF [ETX] [STX] OBF [ETX]
This command is for setting the VTR to standby OFF.
STANDBY
ON [STX] OBN [ETX] [STX] OBN [ETX]
This command is for setting the VTR to standby ON.