Pioneer VSX-2014i - Manual (Page 64)

Other connections 10
64
En
1 Use an i.LINK cable to connect one of the i.LINK
connectors on this receiver to an i.LINK connector on
your i.LINK component.
• The arrow on the cable connector body should be
lined up with the arrow to the right of the connector
on the receiver for correct alignment. The i.LINK
cable should be inserted straight into the connector
so that it snaps easily into place. If not connected
properly the receiver will not be able to recognize any
connected components. Note that the i.LINK cable is
fragile and can be broken easily if too much force is
used when connecting.
2 Assign the i.LINK component to the input you
want, then make any necessary output settings on
the component.
See Assigning the i.LINK inputs on page 68 to assign the
component to an input on this receiver. Follow the
operating instructions that came with the component to
make any necessary output settings.
• Unassigned i.LINK components can be selected with
the front panel i.LINK SELECT button or the INPUT
SELECT button on the remote control.
Note
• You can connect several components together using
i.LINK. See Creating an i.LINK network below.
About i.LINK
VSX-2014i model only
i.LINK is a trademark name for IEEE1394, a high-speed
interface for digital audio, video and other data found on
personal computers, digital camcorders, and other kinds
of audio and audio/visual equipment. A single i.LINK
connector can both send and receive data at the same
time, so only one cable is required to connect compo-
nents for two-way communication.
“i.LINK” and the “i.LINK” logo are trademarks of Sony
Corporation.
About PQLS rate control
Pioneer's PQLS (Precision Quartz Lock System)
technology provides high-precision digital audio from
DVD-A, SACD and audio CD sources when you use the
i.LINK interface. A precision quartz controller in this
receiver eliminates distortion caused by timing errors
(jitter), giving you the best possible digital-to-analog
conversion from the digital source.
To take advantage of PQLS, you must have a player
compatible with rate-control, and it must be switched on
and connected to this receiver through the i.LINK
network.
Creating an i.LINK network
Using i.LINK it is possible to chain up to 17 components
together so that the digital audio and control signals
from each component is available to other components
in the network. With the addition of an i.LINK repeater,
it’s possible to connect up to 34 components.
i.LINK connectors come in 4-pin and 6-pin configura-
tions. This player uses the 4-pin connection, but the two
types can be mixed on a network.
This receiver is compatible with i.LINK Audio (A&M
protocol) components, such as DVD players. Note that
when connected to i.LINK MPEG-II TS equipment (such
as a digital satellite tuner), i.LINK DV equipment (such as
a DVD recorder or DV camcorder), or an i.LINK-equipped
personal computer, audio and video signals are not
transmitted, and connecting to these devices sometimes
causes network interruptions. Check the operating
instructions supplied with your other i.LINK components
for compatibility information.
This receiver is DTCP (Digital Transmission Content
Protection) compliant, so you can play DVD-A, DVD-
Video, and SACD i.LINK audio.
ASSIGNABLE
CD
IN
IN
IN
IN
IN
IN
OUT
OUT
CD-R/
TAPE/MD
VIDEO1
DVR /
VCR
DVD/
LD
TV/ SAT
OUT
PRE
OUT
CEN-
TER
CEN-
TER
SUR-
ROUND
SUR-
ROUND
SUR- ROUND BACK
(Single)
FRONT
FRONT
SUBW.
SUBW.
MULTI CH IN
CONTROL
MULTI-ROOM & SOURCE
MONITOR
MONITOR
VIDEO1
DVR /
VCR
T V / SAT
DVD/ LD
IN
IN
IN
VIDEO
COMPONENT
ASSIGNABLE
MULTI- ROOM & SOURCE
AUDIO VIDEO S-VIDEO
RS - 232C
IN
IN
OUT
OUT
OUT
ANTENNA
AM LOOP FM UNBAL 75 Ω
MONITOR OUT
12V TRIGGER
Y
Y
P B
P R
P B
P R
Y
P B
P R
〜 1 2
2
IN 1
R L
R L
R L
R
R
L
L
R
R
L
L
PLAY
PLAY
REC
OUT
REC
IN
OUT
I R
IN
VIDEO
(DC OUT12V/
100mA MAX)
ASSIGNABLE
S400
S400
IN (DVD/
LD)
IN
(CD)
DIGITAL
IN (CD-R/
TAPE/MD)
IN OUT DIGITAL (TV/SAT)
〜
4
3
2 1
1 4
S400
i.LINK-equipped component
VSX_2014TX.book.fm Page 64 Wednesday, June 2, 2004 5:21 PM