Pioneer VSX-2014i - Manual (Page 78)

Additional information 12
78
En
Remote control
When playing Dolby Digital or
DTS sources, the receiver’s
format indicators do not light. • No digital connection, or the digital
connection is incorrect. • Check the digital audio connection (page 16).
• The receiver’s input signal type is set to
analog. • Set the receiver to AUTO or DIGITAL (see Choosing the
input signal on page 33).
• The DVD player is set to output Dolby Digital
and/or DTS audio as PCM. • Check the settings on the player. Set the output for
Dolby Digital and DTS (no PCM conversion). See also the
operating instructions that came with your DVD player.
• The disc has several playback audio tracks;
the one currently playing is actually PCM. • Switch the playback audio channel on your DVD player.
See the operating instructions that came with your DVD
player.
When playing certain discs,
none of the receiver’s format
indicators light. • The audio format of the disc is not 5.1/6.1
channel. • This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
When playing a disc, the
2 PL II or Neo:6 indicator lights
on the receiver.
• The input signal type is set to analog. • Set the receiver to AUTO or DIGITAL (see Choosing the
input signal on page 33).
• A two channel soundtrack is currently
playing. • This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
• The soundtrack currently playing is
encoded using Dolby Surround. • This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
During playback of a Surround
EX or DTS ES source on the
Extended AUTO setting, the EX
and ES indicators don’t light, or
the signal is not properly
processed.
•The source may be Dolby Surround EX / DTS
ES software, but it has no flag to indicate it is
6.1 compatible. • Set to Extended ON (see Using the surround back
channel (Extended mode) on page 34) then switch to the
THX Surround EX or Standard EX listening mode (see
Listening in surround sound on page 30).
Symptom Cause Remedy
Symptom Cause Remedy
Cannot be remote controlled. • The remote control batteries have worn out. • Replace the batteries (see Loading the batteries on
page 7).
• Too far away or improper angle of operation. • Operate within 7 meters and a 30º angle of the remote
sensor on the front panel (see Operating range of remote
control unit on page 29).
• There is an obstacle between the receiver
and the remote control. • Remove the obstacle or move to another place.
• Strong light such as fluorescent light is
shining onto the unit's remote control sensor. • Avoid exposing the remote sensor on the front panel to
direct light.
• Something is plugged into the CONTROL IN
jack.
• Unplug the cable from the CONTROL IN jack and use
remote normally (see Operating other Pioneer components
on page 22).
• VSX-2014i model only – The IR receiver type
is mismatched with the setting.
• Disconnect the IR receiver from the rear panel or set to
the other IR receiver type (see
Multi Room Setup on
page 71).
Other components can't be
operated with the system
remote. • The preset code settings are wrong. • Input the correct preset code.
• The batteries wore out and the system
settings were cleared. • Reset the proper system settings.
The SR cable is connected, but
the connected components can’t
be operated with the remote. • The SR cable hasn't been connected
properly. • Reinsert the SR cable, making sure it’s connected to the
right jack (see
Operating other Pioneer components on
page 22).
• The rest of the component connections
have not been made. • Make sure an analog connection has been made
between the units.
• The component you have hooked up is not a
Pioneer product. • This feature only works with Pioneer products.
VSX_2014TX.book.fm Page 78 Wednesday, June 2, 2004 5:21 PM