Other settings 11 – Pioneer VSX-2014i User Manual
Page 68
Other Settings
11
68
En
Assigning the component video inputs
• Default settings:
Component 1
–
OFF
Component 2
–
OFF
If you used component video cords to connect your video
equipment you must tell the receiver which device it is, or
else you may see the S-video or composite video input
instead of the component video signal.
1
Select ‘Component Input’ from the Input Assign
menu.
The illustration above shows the VSX-2014i OSD.
2
Select the number of the component video input
to which you’ve connected your video component.
Select between
DVD/LD
,
TV/SAT
,
DVR
,
VIDEO1
or
OFF
.
• The numbers correspond with the numbers beside
the inputs on the back of the receiver.
3
Select the component that corresponds with the
one you connected to that input.
• Use the
/
(cursor left/right)
buttons and
ENTER
to do this.
• Make sure you have connected the audio from the
component to the corresponding inputs on the rear
of the receiver.
• If you connect any source component to the receiver
using a component video input, you should also have
your TV connected to this receiver's component video
MONITOR
output.
4
When you're finished, press RETURN.
You will return to the Input Assign menu.
Assigning the i.LINK inputs
VSX-2014i model only
If you assign i.LINK-equipped components to an input
(for example
DVD/LD
), you will be able to select both
audio and video signals from i.LINK-equipped
components using the corresponding
MULTI CONTROL
button.
1
Select ‘i.LINK Input’ from the Input Assign menu.
2
Select an i.LINK-equipped component.
When a number of i.LINK-equipped components are
connected to your receiver, the i.LINK-equipped
component you are looking for might be listed on
additional display screens.
• If no i.LINK-equipped components are connected,
you won’t be able to assign any inputs.
•
i.LINK
is displayed after unassigned device names
(e.g.
DV-868AVi [i.LINK]
).
• If a connected devices cannot output (playback) a
source using the i.LINK connection,
[- - - -]
is
displayed after the input device name (e.g.
DV-
868AVi [- - - -]
). Non-compatible devices cannot be
assigned to inputs.
• When the cables for an assigned input device
become loose or the power is cut to the device, an
asterisk (
∗
) appears before the device name (e.g.
∗
DV-868AVi [DVD/LD]
).
3
Select the component that you want to assign.
Use the
/
(cursor up/down)
buttons and
ENTER
.
When you assign an i.LINK-equipped video component,
select the input source to which you have connected the
video signal from the component.
• If you assign an i.LINK input to a certain function (for
example
DVD/LD
) then any digital inputs previously
assigned to that function will automatically be set to
i.LINK
(not assigned).
• The
TUNER
input cannot be assigned.
4
When you're finished, press RETURN.
You will return to the Input Assign menu.
5. Input Assign
[
a . Digital Input
]
[
b . Component Input
]
[ c . i. LINK Input
]
5b. Component Input
Component-1 [
DVD/LD
]
Component-2 [
OFF ]
5. Input Assign
[
a . Digital Input
]
[ b . Component Input
]
[
c . i. LINK Input
]
5c. i.LINK Input (1/1)
( End )
1 DV - 868AVi
[
DVD/LD
]
2 DV - S858Ai
[ i.LINK ]
( Top)
VSX_2014TX.book.fm Page 68 Wednesday, June 2, 2004 5:21 PM