Panasonic SA-XR700 - Manual (Page 24)

24
RQT8743
Enjoying the Home Theater
Digital signals this unit can play:
Dolby Digital (including Dolby Digital Surround EX), DTS (including DTS-ES and DTS 96/24) and PCM (á page 37)
• The unit memorizes whether [SURROUND] has been pressed
on or off for each input source.
• The setting always switches from off to on when the input comes
from a surround source in Dolby Digital, DTS or other formats.
• When you press [SURROUND] off while playing a surround
source (excluding a DVD-Audio source that does not allow
down-mixing), 2-channel mix (2CH MIX) activates.
2-channel mix is cancelled when you turn the unit off or when
you switch input sources.
• The “SURROUND” indicator goes off when the sampling
frequency for the input signal is higher than 96 kHz.
• The number of source channels appears on the display when
a digital signal is input or input sources are switched. (Their
number may not appear depending on the selected source.)
• The unit is compatible with linear PCM 8-channel surround
signals decoded by the BD player and other equipment (up to
96 kHz/24 bit). See the operating instructions for equipment
used for playback.
RECEIVER
AV
SYSTEM
TV
RECORDER
DVD
BD/DVD
PLAYER
ANALOG 6CH
VCR CD
TUNER
BAND
CH
-MENU/-SETUP ENTER
INPUT SELECTOR VOLUME
BI-AMP SURROUND
SURROUND SPEAKERS
AUTO DETECTOR
TUNE AUX
ADVANCED DUAL AMP
AUTO SPEAKER SETUP
SETUP MIC
HDMI
RETURN
SURROUND SPEAKERS ENTER - MENU/ - SETUP
AUTO DETECTOR RETURN TUNE
AUX S VIDEO VIDEO L - AUDIO - R SETUP MIC
“SURROUND”
“BI-AMP”
“ADVANCED DUAL AMP”
INPUT SELECTOR
A B
SPEAKERS
SURROUND
VOLUME
“ ”
1
To turn the unit on
Press
The “SURROUND” indicator lights on (factory
setting).
• The standby indicator “^” goes off when you turn the unit on.
Do not forget to perform speaker detection when you play
a source with the unit for the first time or when you change
the number of connected speakers (á pages 10 and 22).
2 To select “SPEAKERS A”
Press to switch “ ” on.
To select “SPEAKERS B”
Press [SPEAKERS B].
( á page 25)
To use bi-wire speakers (á page 20)
To enjoy BI-AMP stereo sounds
See page 25. Press [SPEAKERS A] or [SPEAKERS B] to switch
“
” on.
3 To switch input sources
• Select the connected terminal when the names of the
terminal and equipment you wish to use for playback
do not match.
Turn
• When you select “ DVR ”, “ DVD RECORDER ” scrolls across
the display once.
• You can also select an input source using the remote control ( á page 5).
To use a DVD recorder with built-in VCR (á page 17)
• To play a DVD: select “
DVR ”
• To play a video cassette: select “ VCR ”
4 Play the selected input source. To switch between 2-channel
stereo playback and surround
playback
Press [SURROUND].
5 To adjust the volume
Turn
Volume range:
– – dB (minimum),
–79dB to 0dB (maximum)
To finish the Home Theater
Be sure to reduce the volume and press [8] to turn the unit to standby.
8
Note
A
SPEAKERS
A
A
SPEAKERS
A B
A B
SPEAKERS
BI-WIRE
INPUT SELECTOR
(e.g.)
AUX
CD TV/STB
BD/DVD DVR VCR
TUNER AM TUNER FM
VOLUME
Note
Subwoofer
Number of surround and surround back channels
Number of front and center channels
Enjoying the Home Theater
ENGLISH
SA_XR700_EG_GN_ (RQT8743_B)ver.3.fm 24 ページ ２００６年８月３１日 木曜日 午前９時７分