Panasonic SA-XR700 - Manual (Page 45)

45
RQT8743
Troubleshooting guide
ENGLISH
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not
solve the problem, consult your dealer for instructions.
Pages
No power. • Ensure the AC mains lead is connected. 9
No sound.
Sound is distorted.
• Turn the volume up.
• Check connections to speakers and other equipment.
• Turn on the speakers.
• Select the correct source.
• Change DIG INPUT setting to suit the type of connection you have made.
• Check that the digital signals can be decoded by this unit.
• Turn the muting off.
• Turn PCM FIX off.
• Recording of some DVD-Audio may not be possible due to copyright protection.
12, 24
7 to 9, 14 to 21
12, 24, 25
12, 24
35
37
29
35
–
Sound stops.
“OVERLOAD ” appears on the
display for about a second, and
the unit turns off.
• Determine and correct the cause, then turn the unit on.
Causes include:
- Shorting (bare wires touching) of positive and negative speaker wires.
- Using speakers with an impedance lower than that rated for this unit.
- Straining of the speakers through excessive volume or power.
- Using the unit in a hot environment without proper ventilation.
á Consult your dealer if the problem occurs again after switching the unit on.
8
9, 20
–
–
Analogue input becomes distorted and
the message “OVERFLOW ” appears on
the display during playback.
• Switch the attenuator on. 36
“F76 ” appears on the display and
the unit turns off.
• Turn the unit off, disconnect the AC mains lead, and consult your dealer. –
“F70 ” appears on the display. • Turn the unit off, disconnect the AC mains lead, and consult your dealer. –
“REMOTE 2 ” or “REMOTE 1 ”
appears on the display.
• Match the codes on the main unit and the remote control. 44
Display is dim. • Cancel “ DIMMER ”. 29, 31
Clicking sound is heard during
play.
• Depending on the input signal when playing DVD etc., the ADVANCED DUAL AMP function changes
automatically. A clicking sound is heard when it changes. This does not mean a problem with the unit.
á You can also set the unit against automatic ADVANCED DUAL AMP operations.
–
34
“MEASURING ERROR ” appears
on the display.
• A speaker is too far. Check speaker locations.
• An error occurred from a cause that cannot be identified. Perform the auto speaker setup again. 22, 23
–
When speaker distances are set (á page
33), “– ” appears on the display with the
speaker name such as “L 3.0 – ”.
• It appears when polarity of a speaker is automatically adjusted.
á
You can set speakers against automatic polarity adjustment. 34
When speaker distances are set (á page
33), “OVER ” appears on the display.
• It appears when the measured distance exceeds 15 meters.
Check the speaker location.
–
Sound is not heard from the
center, surround or subwoofer
speakers.
• Ensure the speaker settings for your speakers are correct.
• Confirm Dolby Pro Logic , NEO:6, or SFC settings, and select an adequate mode.
• Press [SURROUND] on when you play 2-channel stereo sources.
10, 22, 23, 33
26 to 28
12, 24
Sound is not heard from the
surround back speaker.
• Ensure the speaker settings for your speakers are correct.
• Press [SURROUND] on. 10, 22, 23, 33
12, 24
Dolby Pro Logic , NEO:6, and
SFC are unavailable.
• Check if the center speaker, surround speakers, and surround back speakers are connected properly.
• Press [SPEAKERS A] on.
• You cannot use Dolby Pro Logic , NEO:6 or SFC on sources containing PCM signals with the sampling
frequency of 192 kHz.
• Cancel DVD ANALOG 6CH playback.
• You cannot use the effect when the input source contains dual audio signals in Dolby Digital or DTS formats.
9
12, 24
–
25
–
There is no DTS audio output.
There is audio output, but the DTS
decoder indicator is not lit.
• Set the DTS Digital Audio Output setting on the DVD player or DVD recorder to “Bitstream”. –
Sound is distorted when using the
Sound Field Control (SFC).
• Depending on the input source, sound may be distorted if you increase the SFC effect level. If this
happens, decrease the SFC effect level.
28
The radio cannot be tuned in or
there is a lot of noise and
interference.
• Connect the appropriate antenna. (You may need an outdoor antenna or one with more elements.)
• Adjust the position of the FM or AM antenna.
• Reduce the treble.
• Turn off nearby televisions, video decks, DVD recorders, DVD players, and satellite receivers.
• Separate the antenna from other cables, cords, and appliances.
21
21
31
–
–
There is a lot of noise when
listening to AM.
• Try changing the BEAT PROOF mode. 39
The correct AM frequency cannot
be tuned in.
• Change the frequency step to suit your area when AM is selected. 38
When using an HDMI connection,
the first few seconds of sound is
cut off.
• Should you be playing a chapter on a DVD:
- Change the audio output setting on the DVD player or DVD recorder from “Bitstream” to “PCM”.
(6.1-channel sources will however be played as 5.1-channel.)
- Select “ PCMFIX ” as instructed in “Setting input signals” when you play 2-channel stereo sources.
–
35
“U70-1-1 ” appears on the display. • The equipment connected by the HDMI cable is not compatible with the unit’s copyright protection technology. –
“U70-1-2 ” appears on the display.
• The unit has received a signal for a picture format that is incompatible with the HDMI connection. Check
the settings of the connected equipment.
–
“U70- 3 ” appears on the display.
• Should anything unusual happen using an HDMI connection:
Consult your dealer if the sign remains on the display after these steps.
- Turn the connected equipment off and on again.
- Pull out the HDMI cable then reinsert it.
- Reduce the number of equipment connected in series to the HDMI terminal if exceeding 2 units.
–
7, 13
–
The unit does not work properly.
• The unit does not work properly when wrong cords are in HDMI input and output terminals. Turn the unit
off, unplug the AC mains lead, and make connections again.
7, 13
HDAVI Control does not function
properly.
• Connect the unit to your TV (VIERA) using the HDMI cable, switch the TV on, unplug the unit’s AC mains
lead, and insert it into a household mains socket again.
–
The equipment connected to the
unit’s “HDMI (BD/DVD PLAYER) IN”
terminal turns on and off by itself.
• Some of the linked operations apply to the connected equipment that is HDAVI Control compatible. To
prevent this, set the connected equipment (DVD recorder (DIGA) and others) against HDAVI Control.
–
The remote control doesn’t work. • Replace the batteries if they are worn. 5
Other products respond to the
remote control.
• Change this unit’s remote control code to “ REMOTE 2 ”. 44
SA_XR700_EG_GN_ (RQT8743_B)ver.3.fm 45 ページ ２００６年８月３１日 木曜日 午前９時７分