Installation, Reinstall the lens hood, Aud io – NEC GT6000 User Manual
Page 24: Audio, Lens shift defection switch
2-7
IN
OUT
REMOTE 2
AC IN
AUD
IO
AUD
IO OUT
R
R/C
r
G/Y
B/C
b
V
H/HV
R
L/MONO
R
L/MONO
R
L/MONO
L/MONO
DVI
RGB OUT
RGB
1
RGB
2
VID
EO
S-V
IDE
O
AUD
IO
SLOT 1
SLOT
2
4
3
IN
OUT
REM
OTE
2
AC IN
AUD
IO
AUD
IO O
UT
R
R/C
r
G/Y
B/C
b
V
H/H
V
R
L/MO
NO
R
L/MONO
R
L/MONO
L/M
ONO
DVI
RGB
OU
T
RGB
1
RGB
2
VID
EO
S-V
IDEO
AUD
IO
SLO
T 1
SLO
T 2
2
1
4. Reinstall the lens hood.
q Remove the front lens cap from the lens unit.
w Insert the lens hood so that the grooves on the 4 corners of the lens hood
are properly lined up with the 4 catches on the projector.
e Secure the 2 screws using the hexagonal driver.
This completes installation. If necessary, put the lens hood cap on the lens
hood.
3
PC CONTROL
IN
IN
OUT
OUT
SC TRIGGER
REMOTE 2
REMOTE 1
LAN
AC IN
USB
(
MOU
SE/H
UB
)
USB
(
PC
)
PC CARD
1
2
AUD
IO
AUDIO OUT
R
R/C
r
G/Y
B/C
b
V
H/H
V
R
L/M
ONO
R
L/M
ONO
R
L/M
ONO
L/M
ONO
DVI
RGB OUT
RGB
1
RGB
2
VID
EO
S-V
IDE
O
AUD
IO
SLOT 1
SLOT 2
2
PC C
ONT
ROL
IN
IN
OUT
OUT
SC T
RIG
GER
REM
OTE
2
REM
OTE
1
LAN
AC I
N
USB
(
MOUSE/HUB
)
USB
(
PC
)
PC C
ARD
1
2
AUDIO
AUD
IO O
UT
R
R/Cr
G/Y
B/Cb
V
H/H
V
R
L/M
ONO
R
L/M
ONO
R
L/M
ONO
L/M
ONO
DVI
RGB
OU
T
RGB 1
RG
B 2
VID
EO
S-V
IDEO
AUDIO
SLO
T 1
SLO
T 2
1
Lens shift defection switch
2. Installation
3. Mount the lens unit on the projector and connect the extension cable attached to the projector.
q Remove the lens cap from the rear end of the lens unit.
NOTE: Leave the front lens cap for protection while mounting the lens unit.
w Insert the lens unit so that the 4 screws on the lens unit are properly lined up with the 4 holes on the lens mount.
e Secure the 4 screws using the hexagonal driver.
r Insert the connector of the lens unit fully into the socket of the extension cable attached to the projector.
NOTE: The GT13ZL, GT19ZL, GT24ZL and GT34ZL optional lenses have one connector. The B type lenses (GT13ZLB, GT24ZLB and GT34ZLB) and
GT20ZL have two connectors.
To insert the connector into the 4-pin socket on the right side.
CAUTION: There is a lens shift detection switch for the moving
gears of the lens shift motors used to reduce the risk of pinching
fingers. Do not defeat this feature.