ROTEL RX-1052 - Manual (Page 18)

18 RX-1052 AM/FM Stereo Receiver
LABEL Button H
The LABEL button on the remote is used with
the ENTER button in programming custom
labels for the input buttons. These custom la-
bels appear in the front panel display when
an input is selected.
ENTER Button I
The ENTER button on the remote serves two
functions.
To adjust the tone settings, repeatedly press
the ENTER button until BASS or TREBLE is
displayed. Then, use the CHARACTER +/–
buttons to increase or decrease the selected
tone setting.
The ENTER button is also used following the
press of the LABEL button in programming
custom labels.
BAND Buttons 5 O
Press the BAND button on the front panel or
the remote to toggle between AM and FM
reception.
TUNING Buttons 4 M
The TUNING buttons on the front panel or the
remote control provide two different tuning
functions, depending on the mode of opera-
tion: frequency tuning or preset tuning.
MEMORY Button = F
The front panel MEMORY button and the MEM
button on the remote are used with the NU-
MERIC buttons to store station presets.
NUMERIC Buttons E
The NUMERIC buttons on the remote are used
to enter the number of a memorized station
preset or for direct entry of a station frequen-
cy. These buttons are also used for operating
Rotel CD and DVD players.
DIRECT Button P
The DIRECT button on the remote is used with
the NUMERIC buttons for direct entry of a sta-
tion frequency in AM/FM tuning.
MONO Button - G
The MONO button on the front panel or the
remote toggles the FM mode from stereo re-
ception to mono reception.
TUNE/PRESET Button 0
T/P Button N
The front panel TUNE/PRESET or remote con-
trol T/P button toggle between FREQUENCY
tuning and PRESET tuning modes.
CD/DVD Buttons K
The STOP . , PLAY / , TRACK { } , and
RANDOM buttons on the remote are used for
operating Rotel CD and DVD players. They are
not used in operating the RX-1052.
CHARACTER +/– Buttons M
The CHARACTER +/– buttons on the remote
have three functions:
They can be used in selecting an input for re-
cording or remote zones when used following
a press of the SEL buttons.
They can be used to adjust the TREBLE or BASS
following selection of tone controls with the
ENTER button.
They can be used to select characters in cus-
tom input labels following a press of the LA-
BEL button.
PTY, TP and TA Buttons TUV
These buttons are used for the advanced search
options available with the RDS system on some
FM broadcasts. See RDS Reception in the Ad-
ditional Features section for more details
Basic Operations
This section covers the basic operating controls
of the RX-1052 and the remote.
Power and Standby On/Off
2\ A
The rear panel POWER switch on the RX-1052
is a master power switch. The switch must be
in the ON position for the unit to operate.
When it is in the OFF position, the unit is ful-
ly off and cannot be activated from the front
panel or remote control.
In normal operation, the rear panel POWER
switch is always left in the ON position. The
RX-1052 is activated and deactivated using
the front panel STANDBY button or the re-
mote ON/OFF buttons. When activated, the
RX-1052 is fully functional and the front pan-
el display illuminated. When deactivated, the
unit goes into a standby mode, with minimal
power applied to the microprocessor.
NOTE: When the unit has AC power applied
and the rear panel POWER switch is on, the
front panel STANDBY LED lights, regardless
of whether the unit is in standby mode or
activated.
The front panel STANDBY button functions as
a toggle switch. Press the button to activate
the unit; press again to put the unit in standby
mode. The ON/OFF buttons on the remote
serve the same function, but provide discrete
ON (active) or OFF (standby) commands.
NOTE: When using the Zone 2 – 4 capabil-
ity of the RX-1052, standby is independent
for the main room and the remote zones.
ON/OFF commands sent from the remote in
the main room will not affect the other zones.
Pressing the ON/OFF buttons on a remote
located in a remote zone will only affect that
zone and not the main room. To switch
all zones to standby mode from any
room, press and hold the OFF button.
When a remote zone is activated, the Zone
LED on the front panel lights.
There are three available power mode op-
tions, which may be useful in configuring the
RX-1052 for special system configurations.
See the Setting Power Mode topic for addi-
tional details.
Volume Adjustments w C
The listening volume of the RX-1052 can be
adjusted from the front panel or the remote.
Front Panel: Rotate the front panel VOL-
UME knob clockwise to increase the volume,
counterclockwise to decrease.
Remote: Press the VOL UP button to increase
the volume; press the VOL DOWN button to
decrease.
With any input other than the Tuner, the Vol-
ume setting is displayed as two digits follow-
ing the input name:
Example: VIDEO 1 45
When adjusting the volume with the tuner in-
put selected, the tuning frequency display is
temporarily changed to a volume indication:
Example: VOLUME 45
NOTE: The VOLUME controls can be used to
change the volume in the remote zones from
the main room. Press the SEL button repeat-
edly until the desired zone appears in the
front panel display, then adjust the volume.
After 10 seconds, the VOLUME control re-
verts to normal operation. The default zone
volume is 60.