Yamaha NOT FOND DSP-Z11 - Manual (Page 118)

Using multi-zone configuration
118
En
■ Adjusting the tonal quality of Zone 2, Zone 3, or
Zone 4
1
Press M
TONE CONTROL on the front panel.
2
Press I
PROGRAM repeatedly to select the high-
frequency response (TREBLE), the low-frequency
response (BASS).
3
Rotate I
PROGRAM to adjust the high-frequency
response (BASS).
Control range: –10.0 dB to +10.0 dB
■ Using the Zone OSD
You can browse and select the iPod or network/USB contents by
using the Zone OSD.
1
Set the operation mode selector to F
SOURCE and
then press the desired input selector button (3).
2
Press K
DISPLAY on the remote control to turn on
the Zone OSD.
3
Press 9k / n / l / h and 9
ENTER repeatedly to
navigate the menu on the Zone OSD.
• The OSD menu appears in English even if you set “LANGUAGE” to “JAPANESE”
or “RUSSIAN” (see page 120).
• There are some characters that cannot be displayed in the front panel display or in the
OSD of this unit. Those characters are replaced with underscores “_”.
• You can set the time for which the Zone OSD is displayed in the Zone video monitor
by using “On Screen” in “Manual Setup” (see page 90).
y
• Short message displays are also appears in the Zone video monitor. Use “Zone OSD”
in “Manual Setup” to select that this unit displays the operational information of all
zones or Zone 2 only (see page 92).
• You can display the status of the selected zone. Set the operation mode selector to
FAMP and then press KDISPLAY.
Use this feature to play the main zone sources in the other zones
simultaneously. This feature is useful to play back a back ground
music in multiple zone in a home party.
1,2,3 ··· In the party mode, this unit distributes the same sources
to the zones which join the party mode.
4 ··· You can also operate the specific zone separately when
this unit is in the party mode.
Turning on the party mode
Press C
PARTY on the remote control to turn on the
party mode.
“PARTY MODE ON” appears in the front panel display and then
the main zone and the zones which join the party mode are turned
on.
Turning off the party mode
Press C
PARTY again to turn off the party mode.
“PARTY MODE OFF” appears in the front panel display and then
the main zone and the zones that joins the party mode are turned off.
y
When this unit is in the party mode, the audio signals that is input at the HDMI IN jacks
or DIGITAL IN jacks are output at the ZONE OUT jacks.
• If you select “MULTI CH” as the input source, this unit does not output any sounds
when this unit is in the party mode.
• When you change the input source of the zone that joins the party mode, the input
source of the main zone also changes same as the operated zone.
• When this unit is in the party mode, no signals are not output at the OUT (REC)
jacks.
Operate the following operations after activating the Zone 2, Zone 3, or Zone 4
operation mode.
Notes
>
>
>
PC/MCX
NET RADIO
USB
TOP
>
>
>
PC/MCX
NET RADIO
USB
TOP
Using the party mode
Before performing the following operations, set the operation mode selector on the
remote control to F AMP.
Notes
Selecting the zones joining the party mode
You can select the zone that joins the party mode by using the
“Party Mode Set” parameters. If a zone does not join the party
mode, you can play back a source in the zone independently
from the main zone. See page 91 for details.
MASTER MAIN ZONE
INPUT
ON OFF
MIC OPTIMIZER
AUDIO SELECT SPEAKERS A B
YPAO SILENT CINEMA PHONES
ON/OFF PURE DIRECT
VOLUME
MULTI ZONE
STRAIGHT TUNING MODE ZONE ON/OFF MENU TONE CONTROL ZONE CONTROLS REC OUT/
ZONE 2 MEMORY FM/AM EDIT PRESET/TUNING EFFECT DISPLAY MAN'L/AUTO CATEGORY SEARCH MODE
PUSH ENTER
PROGRAM
R L OPTICAL
HDMI IN USB AUDIO VIDEO AUX S VIDEO VIDEO ZONE 3 ZONE 4 ZONE 2
1 2
3 4