Yamaha NOT FOND DSP-Z11 - Manual (Page 91)

Graphical user interface (GUI) menu
91
En
Ad
v
a
nce
d
Op
eratio
n
■ Wall Paper (Wall paper)
Use this feature to display the wall paper or gray background in
your video monitor when there is no video signal being input.
When “Conversion” is set to “Off”, no background is displayed even if “Wall Paper” is
set to other than “None”.
Use this menu to set the functions of the multi-zone configuration.
■ Speaker B (Speaker B setting)
Use this feature to select the location of the FRONT B speakers.
• If you connect headphones to the PHONES jack on this unit, the sound is output from
both the headphones and the speakers connected to the EXTRA SP terminals when
“Speaker B” is set to “ZoneB”.
• If a sound field program is selected when “Speaker B” is set to “ZoneB”, this unit
automatically enters the Virtual CINEMA DSP mode (see page 60).
■ Zone SP Assign (Zone speaker assignment)
Use this feature to assign the speaker terminals for Zone 2, Zone 3,
and Zone 4. See page 116 for details.
■ Party Mode Set (Party mode settings)
The party mode enables you to play the same source in multiple
zones simultaneously (see page 118). Use “Party Mode Set” menu
to configure the functions of this unit when this unit is in the party
mode.
Main 11ch Stereo (Main zone 11-channel stereo)
Use this feature to select whether the sound field program of the
main zone is fixed to “11ch Stereo” when this unit is in the party
mode.
Target : Zone2/Target : Zone3/Target : Zone4
(Party mode target zone setting)
Use this feature to specify which zone joins to the party mode.
■ Zone2 Set/Zone3 Set/Zone4 Set
(Zone 2/Zone 3/Zone 4 settings)
Zone2 Volume/Zone3 Volume/Zone4 Volume
(Zone 2/Zone 3/Zone 4 volume)
Use this menu to select whether this unit controls the volume level
of the audio signals output at the ZONE OUT (ZONE2, ZONE3, or
ZONE4) jacks.
• When “Zone2 Volume”, “Zone3 Volume”, or “Zone4 Volume” is set to “Fixed”, you
cannot select the following parameters:
– Zone2 Max Vol./Zone3 Max Vol./Zone4 Max Vol.
– Zone2 Initial Vol./Zone3 Initial Vol./Zone4 Initial Vol.
– Zone2 Balance/Zone3 Balance/Zone4 Balance
• Even if you set “Zone2 Volume” to “Variable”, the volume control on this unit does
not function to the output level of the ZONE DIGITAL OUT (COAXIAL) jack (see
page 113).
Zone2 Max Vol./Zone3 Max Vol./Zone4 Max Vol.
(Zone 2/Zone 3/Zone 4 Maximum volume setting)
Use this feature to set the maximum volume level in the Zone 2,
Zone 3, or Zone 4.
Control range: –30.0 dB to +15 .0 dB, +16.5 dB
Control step: 5.0 dB
The “Zone2 Max Vol.”, “Zone3 Max Vol.”, or “Zone4 Max Vol.” setting takes priority
over the “Zone2 Initial Vol.”, “Zone3 Initial Vol.”, or “Zone4 Initial Vol.” setting. For
example, “Zone2 Initial Vol.” is set to –20.0 dB and then “Zone2 Max Vol.” is set to
–30.0 dB, the volume level is automatically set to –30.0 dB when you turn on the power
of this unit next time.
Button Moving direction of the GUI display
9 k Up
9 n Down
9 h Right
9 l Left
Choice Functions
None Does not display any background in your video monitor.
Piano Displays a background image (the photograph of a piano)
in your monitor when there is no video signal being
input.
Horn Displays a background image (the photograph of a horn)
in your monitor when there is no video signal being
input.
Electric Guitar Displays a background image (the photograph of an
electric guitar) in your monitor when there is no video
signal being input.
Gray Display a gray background in your monitor when there is
no video signal being input.
Note
Manual Setup (Multi Zone)
Choice Descriptions
Main Select this setting when you use the speakers connected
to the EXTRA SP speaker terminals in the main room.
This unit outputs the same audio signals at the EXTRA
SP terminals as the FRONT A speaker terminals.
ZoneB Select this setting when you use the speakers connected
to the EXTRA SP speaker terminals in another room.
When you turn off the FRONT A and FRONT B is turned
on, all the speakers including the subwoofer in the main
room are muted and this unit outputs sounds at the
FRONT B terminals only.
Notes
Choice Descriptions
Off Select this setting to select the sound field program in the
main zone as you like.
On Select this setting to fix the sound field program of the
main zone to “11ch Stereo” mode when this unit is in the
party mode.
Choice Descriptions
Disable Select this setting not to join the selected zone to the
party mode. You can select the input source of the
selected zone independently even if this unit is in the
party mode.
Enable Select this setting to join the selected zone to the party
mode. When this unit is in the party mode, the zone
which this unit plays back the same source as the main
zone in the zones join in the party mode.
Choice Descriptions
Fixed Select this setting when you want to control the volume
level of the selected zone on the external amplifier. This
unit fixes the ZONE OUT (ZONE 2 or ZONE 3) volume
level to a standard line level.
Variable Select this setting when you want to control the volume
level of the selected zone on this unit. You can adjust the
ZONE OUT (ZONE 2 or ZONE 3) vo
lume level
simultaneously with CVOLUME +/– on the remote
control.
Notes
Note