Yamaha R-V1103 - Manual (Page 19)

17
English
MAIN OUTPUT terminals
These terminals are for main channel line output. There is no
connection to these terminals when you use the built-in
amplifier.
However, if you drive main speakers with an external stereo
power amplifier, connect the input terminals of the external
amplifier (MAIN IN or AUX terminals of a power amplifier or an
integrated amplifier) to these terminals.
* Output signals from the MAIN OUTPUT terminals are
affected by the use of BASS, TREBLE, BALANCE controls
and BASS EXTENSION switch.
CENTER OUTPUT terminal
This terminal is for center channel line output. There is no
connection to this terminal when you use the built-in amplifier.
However, if you drive a center speaker with an external power
amplifier, connect the input terminal of the external amplifier to
this terminal.
REAR (SURROUND) OUTPUT terminals
These terminals are for rear channel line output. There is no
connection to these terminals when you use the built-in
amplifier.
However, if you drive rear speakers with an external stereo
power amplifier, connect the input terminals of the external
amplifier (MAIN IN or AUX terminals of a power amplifier or an
integrated amplifier) to these terminals.
SUBWOOFER OUTPUT terminal
This terminal is for connecting with the input terminal of an
amplifier for driving a subwoofer.
When the input signals to this unit are in normal 2-channel
stereo, this terminal outputs only frequencies below 150 Hz
(200 Hz for General model only) from the main and center
channels. When discrete signals are input to this unit and are
selected as the input source, this terminal outputs signals from
the subwoofer channel.
Note
Output level of signals from all of these terminals are
adjusted by the use of VOLUME control on the front panel
or MASTER VOLUME keys on the remote control
transmitter.
Ⅲ
OUTPUT terminals (for driving speakers with external amplifiers)
Be sure to switch this only when the power to this unit is not on.
Select the position whose requirements your speaker system
meets.
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE
STANDBY/ON SWITCH IS PRESSED
The IMPEDANCE SELECTOR switch may not be set to
either end closely. If so, set the switch to either end closely.
(Upper position)
Rear: The impedance of each speaker must be 6
Ω
or
higher.
Center: If you use one center speaker, the impedance of the
speaker must be 6
Ω
or higher.
If you use two center speakers, the impedance of
each speaker must be 3
Ω
or higher.
Main: If you use one pair of main speakers, the impedance
of each speaker must be 4
Ω
or higher.
If you use two pairs of main speakers, the impedance
of each speaker must be 8
Ω
or higher.
(Lower position)
Rear: The impedance of each speaker must be 8
Ω
or
higher.
Center: If you use one center speaker, the impedance of the
speaker must be 8
Ω
or higher.
If you use two center speakers, the impedance of
each speaker must be 4
Ω
or higher.
Main:
<
Except Canada model
>
If you use one pair of main speakers, the impedance
of each speaker must be 8
Ω
or higher.
If you use two pairs of main speakers, the
impedance of each speaker must be 16
Ω
or higher.
< For Canada model only >
The impedance of each speaker must be 8
Ω
or
higher.
Ⅲ
IMPEDANCE SELECTOR switch
SWITCHED
I20V 60Hz
I00W MAX. TOTAL
AC OUTLETS
IMPEDANCE SELECTOR
: 6 Ω MIN. /SPEAKER
SINGLE: 6 Ω MIN. /SPEAKER
DUAL: 3 Ω MIN. /SPEAKER
A OR B: 4 Ω MIN. /SPEAKER
A B: 8 Ω MIN. /SPEAKER
SET BEFORE POWER ON
REAR
CENTER
MAIN
: 8 Ω MIN. /SPEAKER
SINGLE: 8 Ω MIN. /SPEAKER
DUAL: 4 Ω MIN. /SPEAKER
A OR B: 8 Ω MIN. /SPEAKER
A B:I6 Ω MIN. /SPEAKER
REAR
CENTER
MAIN
MAIN CENTER REAR
(SURROUND)
OUTPUT
SUB
WOOFER
(U.S.A. model)
IMPEDANCE SELECTOR