ZELMER 619 - Manual (Page 89)

 88
− Insert the water filter into the tank and place the tank on the
base.
− Close the top lid.
− Insert the ending of the hose in the position where the tops marks on
the hose ending and tank cover each other and turn it right or left,
so that the marks change position in reference to each other.
− Połącz:
a. sucking tubes, b. tube with hose, c. tube with chosen nozzle or brush.
− Insert the hose stub into the valve inside the vacuum
cleaner base.
− Make sure that the stub fastening is exactly locked in the seating,
ATTENTION!!! In case of difficulties in a/m elements connection lubricate the sealing with i.e.
Vaseline grease, water, etc.
− Take the connection cord plug and remove it from the vacuum cleaner.
ATTENTION!!! Be careful during pulling the cord out, the yellow mark on the
cord show the end of the cord.
Further trials (pulling) can lead to damage the cord.
− Insert the plug to the mains supply receptacle and switch the vacuum cleaner on
pressing the on/off button.
ATTENTION!!! The vacuum cleaner is equipped with a float, which shall
automatically block the suction, if the foam filter is very dirty.
It is indicated with increased engine rotation.
In such situation:
− Switch off the vacuum cleaner pressing the on/off button and unplug it.
− Turn the ending of the hose up to the position where the tops
marks on the
hose ending and tank cover each other and remove the hose from the tank.
− Open the top lid and remove the front tank.
− Remove the water filter and take the foam filter out of it.
− Clean the a/m filters thoroughly (see the “After operation”
section.
− Release the hook of the filter housing bottom and remove the rubbish.
− If the rubbish have been collected to the paper bag before, please release the
top cover hooks 1 following the above mentioned activities (Item”A”).
− Pour dirty water out including the dirtiness form the tank and
rinse the tank.
− Pour clean water, insert the water filter, place the tank on the base and close the
top lid.
− Insert the plug to the mains supply receptacle, switch the vacuum cleaner on and
continue vacuuming.
ATTENTION!!! The float can also operate during sudden movements, sharp pulling, hitting, or
crossing the doorsteps.
89
In such case:
− Switch the vacuum cleaner off for several seconds and then switch it on again and continue
vacuuming.
LIQUID SUCTION
If you want to use your vacuum cleaner for liquid suction, please prepare it like for dry surface
cleaning, apart from:
1. Front tank should be empty (without water).
2. Do not apply any filtration pads or paper bag.
3. Apply the spraying nozzles (big or small), described below.
ATTENTION!!! In any case do not start up the vacuum cleaner with full tank! Do not pick up big
amount of liquid in one cleaning (i.e. with hose immersed in water).
If „MAX” level is exceeded during liquid suction, the float shall automatically block the suction.
In such case:
− Apply the same method as in case of suction blocking caused by dirty foam filter (increased engine
rotation).
WET CLEANING – accessories
Big spraying nozzle – It is applied for water suction and wet cleaning.
Small spraying nozzle – It is applied for wet
cleaning of small upholstered surfaces, i.e. chairs,
armchairs, sofas, car upholstery, etc.
Brush strip – to be fitted on big spraying nozzle. It is applied for water suction from
hard surfaces, i.e. parquet, lino, ceramic tiles, etc. and wet cleaning.
Two sucking tubes set (for washing function) – they
connect the hose with proper nozzle. You can use both or
one tube depending on your needs.
Sucking hose (for washing function) – is the basic equipment of the vacuum
cleaner. The flexibility makes possible to manipulate with different parts of
accessories. The hose handle includes:
1. The two-functions button:
− Water flow to nozzle releasing – press the button
according to the arrow .
− Water flow to nozzle releasing with buttons stoppage –
press the button and move it back according to the arrow .
2. The inlet with suction power adjusting. Do not open it during water suction or wet cleaning.
Preparations for wet cleaning
Vacuum the surface thoroughly before wet cleaning and then prepare the surface for wet cleaning,
the following way:
− Switch the vacuum cleaner off and unplug it.
− Turn the ending of the hose up to the position where the tops
on the hose
ending and tank cover each other and remove the hose from the tank.
− Open the top lid and remove the front tank.
− Remove the water tank.
− Remove the rubbish from the filter housing cup or remove the paper bag.
Buton
Sucking
hose
Handle
Power suction
regulator