ZELMER 619 - Manual (Page 91)

1 90
− Pour dirty water out including the dirtiness form the tank and rinse the tank.
− Insert the water filter without paper bag and filtration pad.
− Place the tank at the base and close the top lid.
− Remove the nozzle or the brush, which was used earlier
and fit the nozzle for wet clearing on the sucking tube.
− Remove the back tank:
−
open the top lid and bring it to vertical position 1.
− move the tank up and then move it back 2.
− Remove the inlet pin and fill the tank up with cleaning agents
(the powder solution or liquid), according to the label:
1. Powder, cleaning solution preparation: dissolve the content
of the bag in 2,5 – 3l of warm water- temp. up to 45ºC.
2. Cleaning liquid: pour the measured portion of the liquid into
the back tank. 1 pin of liquid for 3,5l water.
− Depending on the applied clearing agent, fill the back tank up with prepared solution or warm water
with temp. up to 45ºC.
− Insert the pin into the inlet in back tank.
ZELMER S.A. warranties good cleaning effect and proper vacuum cleaner operation, only using the
cleaning agents and their amount approved by ZELMER S.A., which is indicated at the label:
− „DYWANOPUC” cleaning powder manufactured by OKTIMA,Poland,
− „CARPEX” cleaning liquid manufactured by ASTRA POLLENA, Poland,
− „FOUNTAINHEAD” cleaning liquid manufactured by Butcher’s, USA
− Place the tank in previous place and push it in to fasten it exactly at the vacuum
cleaner housing.
− Close the top lid.
ATTENTION !!! The vacuum cleaner is equipped by the manufacturer with one
of the a/m cleaning agents only.
CLEANING CARPETS
heck the colours resistance before wet cleaning.
Put a small amount of cleaning agent on white cloth (powder solution or liquid) and clean the carpet in
the least visible place. If the cloth will be coloured, it means that the carpet does not have permanent
colours and can not be cleaned this way.
To protect against foam generation, or when it is generated during cleaning, use the anti-
foaming agent recommended by ZELMER S.A., in amount and way explained at the label:
−
“ANTYPIENIACZ III” provided by OKTIMA Poland,
−
„FOAM-FREE” provided by Butcher’s, US .
ATTENTION!!! The vacuum cleaner is equipped by the manufacturer with one
of the a/m cleaning agents only.
− Remove the brush strip from the nozzle
− Check the right direction of nozzle movement on the carpet, so that it has the least
friction.
− Press the pump on/off button in and switch
the vacuum cleaner on.
ATTENTION!!! You can switch the pump on only, when there is water
inside the back tank. The lack of water is indicated with very noisy pump operation.
− Press the adjusting button at the hose handle to adjust the water flow to the nozzle.
−
Move the nozzle along the carpet with forward and backward movements.
91
ATTENTION!!! In case of finding out that the nozzle does not spray the water although the
pump is on, check if the back tank is properly assembled (push it strong in),
and assembling the stub in the valve at the base. In case of difficulties with
fitting lubricate the seating of back tank valve and the stub sealing.
− Clean the carpet so, that you do not step on the cleaned surface during cleaNing or just after.
ATTENTION!!! The vacuum cleaner is equipped by the manufacturer with one of the a/m
cleaning agents only.
− After cleaning the part of the carpet make a break and dry it with forward and backward movements
of the nozzle. Repeat the activities until the whole surface of the carpet is dried.
− When spraying is finished switch the pump off and press for a moment the button adjusting the
water flow to the nozzle, to release the pressure.
In case of old or especially difficult stains, damp the place with cleaning agent recommended
by ZELMER S.A., up to the moment the foam appear. Then leave for a while and next suck it
out with the vacuum cleaner.
ATTENTION!!! Do not allow the carpet soaking. It can cause the permanent deformation
(rucking).
PLAIN FLOORS CLEANING
− Fit the brush strip on the nozzle.
− Press the pump on/off button in and switch the vacuum cleaner on (as in case of carpets).
− Press the adjusting button at the hose handle to adjust the
water flow to the nozzle.
ATTENTION!!! In case the spraying nozzle is blocked disassemble the
nozzle from the tube and clean (blow) the duct, or replace
the nozzle with a new one.
The set of spare nozzles is attached to the accessories
Nozzle exchange
1. Remove the spraying element and the ring ø 5,6 x 1 from the big (or small) spraying nozzle,
Press the sprayer with your thumb according to the mark on the nozzle housing.
2. Lubricate the new sprayer including the ring and insert it into the nozzle inlet up to the moment
the hooks are locked.
− Move the nozzle along the cleaned surface with forward and back ward movements.
− Stop the spraying after clearing the part of the floor and suck the solution in, making slow
movements of the nozzle in your direction, until all solution is collected from the floor.
− Continua it until all the floor is cleaned and dried.
− When spraying is finished switch the pump off and press for a moment the button adjusting the
water flow to the nozzle, to release the pressure.
If you preformed wet clearing (picking up wet dirtiness) before finishing operation in the final
stage, suck in abort 1–2l of clean water in order to flush the tubes and hose, and then suck in
the air for a while, in order to dry them.
AFTER OPERATION
− Switch the vacuum cleaner off and unplug it from the mains supply outlet.
− Rewind the cord pressing the rewind button. Hold the plug when rewinding, do not
allow the cord to get entangled and the plug to bump the casing.
− Turn the ending of the hose up to the position where the tops
marks on the hose ending and tank cover each other and remove
the hose from the tank.
−
Remove the hose stub from the base.
−
Press the button and disassemble the tubes.Disassemble the
hose and nozzle similar way.