Teledyne LeCroy STX M6-1 SAS_SATA Protocol Analyzer User Manual User Manual
Sierra m6-4 sas/sata protocol analyzer user manual
Advertising
Table of contents
Document Outline
- Chapter 1
- Introduction
- Analyzer Overview
- Receiving Your Analyzer
- Unpacking Your Analyzer
- Analyzer Features
- LEDs
- Installing Your Analyzer
- Software Installation
- Hardware Setup
- Expandability
- Connecting via Ethernet
- Connecting to a Network
- Connecting using a Hub, Switch, or Similar Device
- Connecting over Different Subnets
- TCP and UDP Ports Must Be Open to Connect over Ethernet
- Launching Your Analyzer
- Operating in Simulation Mode
- Using the Software
- Protocol Analyzer
- Protocol Analyzer Initiator Emulator or Host Emulator
- Performance Analyzer
- Target Emulator or Device Emulator
- Viewing Captured Data
- Chapter 2
- Protocol Analysis
- Easy Mode (Pre-Defined Setups)
- Main Window
- SAS Software Menus and Toolbar
- SATA Software Menus and Toolbar
- Saving a Trace Capture
- Exporting
- Export to Generator
- Export Paired SAS Address Report
- CrossSync Control Panel
- Projects
- Trigger Setup
- Snapshot Mode
- Any Trigger Mode
- Bus Condition
- Symbol
- Primitive
- ATA Command
- Data Pattern
- Protocol Errors
- ATAPI
- Address Frame (SAS only)
- STP Frame (SAS only)
- SMP Frame (SAS only)
- SSP Frame (SAS only)
- SCSI Command (SAS only)
- Timeout (SATA only)
- ATA Command Pattern (SATA only)
- Soft Reset (SATA only)
- FIS (SATA only)
- FIS Pattern (SATA only)
- Sequential Trigger Mode
- Pre-Trigger
- Project Settings
- Add a Project Note
- Advanced Mode (User-Defined)
- Multi - Link Triggering
- Set Timers
- Timeout
- Useful Key Sequences
- Project Settings
- Notes
- Exercise and Capture
- Programming the Initiator or Host Emulator
- Adding Initiator or Host Emulator Commands
- Adding a User-Defined ATA Command
- Adding a SCSI Command (SAS only)
- Adding a User-Defined SCSI Command (SAS only)
- Adding a TASK Command (SAS only)
- Adding an SMP Command (SAS only)
- Adding a Frame
- Adding an Event
- PHY Setting Dialog
- Inserting Instructions
- Phy Reset Sequence and Identification
- Sample Host Emulator Program (SATA only)
- Sample Initiator Emulator Program (SAS only)
- Data Blocks
- Exercising Specific Addresses
- Record and Play
- Error and Command Settings
- ATA Error and Command Settings
- Outgoing ATA Frame Settings
- Incoming ATA Frame Settings
- SCSI Error and Command Settings (SAS only)
- Outgoing SCSI Frame Settings
- Incoming SCSI Frame Settings
- FIS Options (SATA only)
- Initiator Setting Tab (SAS only)
- Host Setting Tab (SATA)
- Project Settings
- Creating a Data Block
- Creating and Editing Data Blocks as Text
- Performance Analysis
- Target and Device Emulation
- Pages Tab
- Error Injection Tab
- Connection Management (SAS only)
- SAS Commands Errors (SAS only)
- ATA Commands Errors (SATA only)
- Outgoing Frame Settings
- Incoming Frame Settings
- SATA Signature (SATA only)
- SATA Signature Errors
- User-Defined Commands Tab
- Target Emulator Settings (SAS)
- Notes Tab
- Run Target Emulation
- Device Emulator Settings (SATA only)
- Project Note
- Using the Power Expansion Card
- Run Device Emulation
- Easy Mode (Pre-Defined Setups)
- Chapter 3
- Display Manipulation
- Viewer Display
- Sample Properties
- Switching Views
- Port Status
- Toolbars
- Status Bar
- Filtering
- Using the Cursors and Bookmarks
- Search
- Display Configuration
- Sample Viewer Configuration
- Set Port Alias
- SAS Address Alias (SAS only)
- Tx Vout
- Software Settings
- General Tab
- Sample Viewer Tab
- Spread Sheet View Tab
- Column View Tab
- Field List View Tab
- Sampling Memory Usage Optimization
- Floating License
- External Trig Setting
- Update STX Board Interface
- Update Sierra Device
- USB IP Setup
- User-Defined Decoding
- Help Menu
- Statistical Report
- Report between Cursors
- Report between Events
- Statistical Report Content
- Report Options
- General Report
- Primitive Report
- Bus Condition Report
- ATA Command Report
- ATAPI Report
- Protocol Error Report
- Others Report
- SSP Transport Report (SAS)
- SMP Transport Report (SAS)
- STP Transport Report (SAS)
- SCSI Command Report (SAS)
- SMP Command Report (SAS)
- Task Command Report (SAS)
- SAS Address Report (SAS)
- Lanes Report (SAS)
- Read/Write Command Report (SAS)
- Performance Report (SAS)
- Performance Report (SATA)
- FIS Report (SATA)
- Queue Command Report (SATA)
- PM Statistic Report (SATA)
- PM Performance Report (SATA)
- Read Write Command Report (SATA)
- Statistical Report Toolbar
- Formatting the Statistical Report View
- Data Report
- Tools
- Find Device
- Chapter 4
- InFusion Overview
- Chapter 5
- Sierra Trainer Traffic Generation
- Sierra Trainer Menus
- Sierra Trainer Main Toolbar
- Setting Up for Generating Initiator Traffic
- Setting Up for Generating Target Traffic
- Creating a Traffic Generation File
- Overview of Generation and Global Settings Files
- Primitive and Frame Definitions
- Starting the Script Editor
- Multi-Port Trainer Script Assignments to Links
- Generating Traffic
- Sierra Trainer Generation Language
- File Structure
- Language
- Generation Block
- Definitions
- Trainer Script Enhancements
- Sierra Trainer Generation Commands
- Generation Options
- Generation Rules Toolbar
- Generation Rules Page: How It Works
- Creating Event Buttons
- Dragging a Button to the Main Display Area
- Assigning an Action
- Generation Rules Pop-Up Menus
- Events and Event Properties
- Setting Complex “Wait For” Conditions
- Find
- Data Pattern Mask and Match
- Find Next
- Search Direction
- Display Options
- Appendix A
- Creating a Pattern Generator File
- Appendix B
- China Restriction of Hazardous Substances Table
- Appendix C
- How to Contact LeCroy
- Index